Giriş

This guide will take you through the steps of removing the touchscreen.

  1. Locate the bay door for the battery on the left side of the laptop.
    • Locate the bay door for the battery on the left side of the laptop.

    Yorum Ekle

  2. Slide the latch to the right and then down to unlock it.
    • Slide the latch to the right and then down to unlock it.

    • Pull out the battery.

    Yorum Ekle

    • Remove the four hinge screws from the back of the computer.

    Yorum Ekle

    • Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver.

    • Pry off the plastic strip which was previously held in place by the screws.

    Yorum Ekle

    • Remove the four hinge screws to allow the hinges to rotate up and move.

    Yorum Ekle

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Remove 16 screws from the top of the closed laptop.

      • 12 Phillips size 1 screws

      • 2 Phillips size 0 screws

      • 2 Torx size 6 screws (T6)

    I found that the Torx screw on my model to be T8.

    Harley - Yanıt

    Is the touchscreen & the LCD 1 piece? or are they separate?

    Chasity Miller -

    • Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.

      • You will need to reapply the silicon adhesive during reassembly to ensure watertight seal.

    Yorum Ekle

    • Pull the top halve of the casing up revealing the inside of the screen

    Yorum Ekle

    • The top half of the case can be removed by sliding the tabs out from under the hinges.

      • This makes unplugging the screen wiring much easier

    Yorum Ekle

    • There are 4 wires that need to be unplugged to remove the screen.

    Yorum Ekle

    • For the first wire, peel back the silver cover tape to reveal the connection.

    Yorum Ekle

    • Pull the wiring away from the connection to release it.

    Yorum Ekle

    • Remove the 3 strips of black tape as shown to reveal connections 2 and 3.

    • Pull the wiring for each away from the connections to remove.

    Yorum Ekle

    • The 4th connection is already visible.

      • Depending on your model it might not be plugged into anything. If it is, remove it the same way the other 3 connections were removed.

    Yorum Ekle

    • Using a plastic opening tool, lift the screen as shown from the case and pull free.

    Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

5 başka kişi bu kılavuzu tamamladı.

Dylan Bloom

Üyelik tarihi: 12-04-2010

262 İtibar

4 adet Kılavuz yazıldı

Takım

Cal Poly, Team 27-93, Amido Spring 2010 Cal Poly, Team 27-93, Amido Spring 2010 üyesi

CPSU-AMIDO-S10S27G93

4 Üyeler

12 adet Kılavuz yazıldı

Bir Yorum

This guide is good for replacing the LCD screen, but it is not complete for the touchscreen panel, which requires some more delicate and precise steps. I think the title of the guide needs to be changed.

Thanks

Alessandro Cervelli - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 Gün: 8

Son 30 Gün: 29

Her zaman: 15,431