Ana içeriğe geç

Parrot AR.Drone 2.0 Central Cross Replacement

Neye ihtiyacın var

Videoya Genel Bakış

  1. Parrot AR.Drone 2.0 Central Cross Replacement, Mainboard and Navigation Board: adım 1, 1 resimden 1.
    • Remove the foam body.

  2. Parrot AR.Drone 2.0 Central Cross Replacement: adım 2, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 2, 2 resimden 2.
    • Disconnect the battery by pulling the two red wires apart.

    • Remove the battery by releasing the battery retaining straps.

  3. Parrot AR.Drone 2.0 Central Cross Replacement: adım 3, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 3, 2 resimden 2.
    • Turn the drone upside down.

    • The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

  4. Parrot AR.Drone 2.0 Central Cross Replacement: adım 4, 3 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 4, 3 resimden 2. Parrot AR.Drone 2.0 Central Cross Replacement: adım 4, 3 resimden 3.
    • Using a spudger, separate the connector for the downward camera.

    • Remove the camera from the body by pulling it off the foam body.

  5. Parrot AR.Drone 2.0 Central Cross Replacement: adım 5, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 5, 2 resimden 2.
    • Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.

    • Use tweezers to carefully remove the ribbon from the connector.

    How can I get that connector, the one it’s disconnected?

    gui txr - Yanıt

  6. Parrot AR.Drone 2.0 Central Cross Replacement: adım 6, 1 resimden 1.
    • Remove the four 8mm torx screws with a T6 bit.

    • Remove the four 8mm philips head screws with a PH00 bit.

  7. Parrot AR.Drone 2.0 Central Cross Replacement: adım 7, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 7, 2 resimden 2.
    • Carefully pull the secondary board from the mainboard.

  8. Parrot AR.Drone 2.0 Central Cross Replacement: adım 8, 3 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 8, 3 resimden 2. Parrot AR.Drone 2.0 Central Cross Replacement: adım 8, 3 resimden 3.
    • Turn the drone right side up

    • Remove the USB connector from the battery retaining straps.

  9. Parrot AR.Drone 2.0 Central Cross Replacement: adım 9, 1 resimden 1.
    • Release the rubber clip holding the USB and battery power cable to the body.

  10. Parrot AR.Drone 2.0 Central Cross Replacement: adım 10, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 10, 2 resimden 2.
    • Avoid using sharp tools near the battery.

    • Push the USB and power cable through the battery panel.

  11. Parrot AR.Drone 2.0 Central Cross Replacement: adım 11, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 11, 2 resimden 2.
    • Turn the drone upside down again.

    • Use a spudger to release the connector and carefully remove the ribbon.

  12. Parrot AR.Drone 2.0 Central Cross Replacement: adım 12, 2 resimden 1. Parrot AR.Drone 2.0 Central Cross Replacement: adım 12, 2 resimden 2.
    • Lift the mainboard up so that you can access the back.

    • Disconnect the first connector with the white wires using a nylon spudger.

    • Disconnect the second connector with the red and black wires using a spudger.

  13. Parrot AR.Drone 2.0 Central Cross Replacement: adım 13, 1 resimden 1.
    • The mainboard is now fully detached and can be removed.

  14. Parrot AR.Drone 2.0 Central Cross Replacement, Central Cross: adım 14, 1 resimden 1.
    • Using a nylon spudger, peel off the four pieces of plastic securing the frame to the body.

  15. Parrot AR.Drone 2.0 Central Cross Replacement: adım 15, 1 resimden 1.
    • Carefully maneuver the four arms of the drone’s central cross until it detaches from the body by pulling apart the foam surrounding the arms.

    between arm 1 and arm 2 there is a little triangle on the central cross, that should point to the front.

    deebee122 - Yanıt

  16. Parrot AR.Drone 2.0 Central Cross Replacement: adım 16, 1 resimden 1.
    • The central cross can now be removed and replaced.

    between arm 1 and arm 2 there is a little triangle on the central cross, that should point to the front.

    deebee122 - Yanıt

Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

David Hoyt

Üyelik tarihi: 04/09/10

4.023 İtibar

43 adet Kılavuz yazıldı

Ekip

Cal Poly, Team 25-89, Amido Spring 2010 Cal Poly, Team 25-89, Amido Spring 2010 üyesi

CPSU-AMIDO-S10S25G89

4 Üyeler

63 adet Kılavuz yazıldı

2 Yorum

If the crossbones are off just a bit would that effect the flight?

John Wurst - Yanıt

So once I have removed the central cross, how do I put it all back together again?? I feel as though this is letting your guide down!!!!

Jacob Kenworthy - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 7

Son 30 gün: 18

Her zaman: 6,135