Eşyalarını Tamir Et Topluluk Mağaza

Pipo Smart S1 Battery Replacement

Giriş

The guide will take you through the process of replacing a dead or defective battery in a Pipo Smart S1 tablet.

Neye ihtiyacın var

  1. Pipo Smart S1 Battery Replacement, Battery: adım 1, 3 resimden 1. Pipo Smart S1 Battery Replacement, Battery: adım 1, 3 resimden 2. Pipo Smart S1 Battery Replacement, Battery: adım 1, 3 resimden 3.

    • Insert an iFixit opening tool between the body and display of the tablet at the bottom of the device where the charging port is.

    • Slide the tool along the gap you are creating, moving to the right direction against the mini USB port.

    Düzenle

  2. Pipo Smart S1 Battery Replacement: adım 2, 1 resimden 1.

    • Gently pry the body of the tablet and pop the back cover open.

    • Lift the back cover of the device and place it on the side.

    Düzenle

  3. Pipo Smart S1 Battery Replacement: adım 3, 1 resimden 1.

    • Lift the edge of the white tape with the iFixit opening tool.

    Düzenle

  4. Pipo Smart S1 Battery Replacement: adım 4, 2 resimden 1. Pipo Smart S1 Battery Replacement: adım 4, 2 resimden 2.

    • Lift the white tape with your fingers, then lift the yellow tape that holds the battery extension.

    Düzenle

  6. Pipo Smart S1 Battery Replacement: adım 5, 1 resimden 1.

    • On the bottom of your tablet, use the Phillips #0 screwdriver to take the two 3mm screws out.

    Düzenle

  7. Pipo Smart S1 Battery Replacement: adım 6, 2 resimden 1. Pipo Smart S1 Battery Replacement: adım 6, 2 resimden 2.

    • Lift the headphone jack and move it to the other side, placing it on the surface you are working on.

    Düzenle

  8. Pipo Smart S1 Battery Replacement: adım 7, 2 resimden 1. Pipo Smart S1 Battery Replacement: adım 7, 2 resimden 2.

    • Use a spudger to pry the battery and detach it from the glue underneath it.

    • Be careful not to pinch the battery—lithium batteries are hazardous and prone to short circuiting, and thus burning and/or exploding.

    Düzenle

  9. Pipo Smart S1 Battery Replacement: adım 8, 1 resimden 1.

    • Lift the battery and place it a little further away from the positive and negative battery wires.

    Düzenle

  10. Pipo Smart S1 Battery Replacement: adım 9, 1 resimden 1.

    • Using your soldering iron, melt the two lead spots to detach the wires.

    • The soldering iron is extremely hot, so handle with caution. Always keep the soldering iron holder next to you when using it so you can return it easily.

    • When reassembling, make sure you solder the right pole to the right spot on the circuit board, as swapping them can burn the motherboard.

    Düzenle

  11. Pipo Smart S1 Battery Replacement: adım 10, 2 resimden 1. Pipo Smart S1 Battery Replacement: adım 10, 2 resimden 2.

    • Remove the two wires. Then remove the battery completely from the device.

    • Make sure you tape the negative and positive battery wires to keep them from short-circuiting.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

3 tane daha katılımcı ile

Ali Alqallaf

Üyelik tarihi: 09/28/16

340 İtibar

3 adet Kılavuz yazıldı

Rozetler: 8

+5 tane daha rozet

Ekip

USF Tampa, Team 3-6, Passmore Fall 2016 USF Tampa, Team 3-6, Passmore Fall 2016 üyesi

USFT-PASSMORE-F16S3G6

3 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 974