Giriş

Use this guide to replace the PlayStation 3 Slim's single cooling fan.

Turn the PS3 over and lay it on its backside.
  • Turn the PS3 over and lay it on its backside.

  • Carefully peel the warranty sticker up off the lower case to reveal a hidden screw cover.

  • To avoid activating the VOID that may come up, heat the sticker carefully to remove and replace it cleanly.

Yorum Ekle

Use the flat end of a metal spudger to pry up the seven screw covers around the edge of the lower case. Use the flat end of a metal spudger to pry up the seven screw covers around the edge of the lower case.
  • Use the flat end of a metal spudger to pry up the seven screw covers around the edge of the lower case.

Yorum Ekle

Remove the seven 37 mm Phillips screws securing the top cover to the lower case.
  • Remove the seven 37 mm Phillips screws securing the top cover to the lower case.

Yorum Ekle

Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening. (Some models may only have three screws)
  • Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening. (Some models may only have three screws)

Its 4 screws beneath the blu-ray

Manuel - Yanıt

Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening.

Daniel Tlapa - Yanıt

Can we edit this to say 4 screws?

revanantwraith - Yanıt

I made the change from three to four screws, but you're able to edit the guides as well. If you want to edit something, you can click the Edit link on the right side of any guide step, or the Edit link at the top right of the page (sandwiched in-between View and History).

Taylor Arnicar -

Do you guys have a guide for the PS3 Slim Model 3001A. The fan is different than this model.

emknight04 - Yanıt

3001a is basically same motherboard but cheaper plastic bd drive other than that its exactly the same until you get to the new slim line

Robert -

Anyone know an online retailer with a competitive price for the replacement fan?

Jared - Yanıt

My PS3 had only three Torx screws. Having four in the diagram was initially confusing. Obviously they made a mid-stream change at some point (mine is several years old now).

corygbooker - Yanıt

I've accidentally removed the ribbon cable from the blu-Ray drive and can not seem to figure out how to reconnect it. Can anyone help?

OneIfByLand - Yanıt

Take the top off the drive, connect the ribbon to the motherboard then replace the drive sliding the ribbon through the slot on the bottom of the drive and reconnect to the laser.

KcXbox Repair -

pls help i have to tear down my ps3 slim but the 4 srews are very hard to take it out because there is a needle in the middle pls hep

Vincent Brabandt - Yanıt

If the screw has a pin in the center, that means it is a security Torx meant to prevent tampering. To remove this screw, follow the guide I have linked below...

http://www.instructables.com/id/Removing...

Telpack - Yanıt

Lift the top cover from its rear edge and rotate it toward the front of the PS3. Lift the top cover off the PS3.
  • Lift the top cover from its rear edge and rotate it toward the front of the PS3.

  • Lift the top cover off the PS3.

Yorum Ekle

Squeeze the AC inlet connector's locking mechanism and pull straight up to disconnect it from the power supply. Squeeze the AC inlet connector's locking mechanism and pull straight up to disconnect it from the power supply.
  • Squeeze the AC inlet connector's locking mechanism and pull straight up to disconnect it from the power supply.

Yorum Ekle

Pull the DC-Out cables straight up to lift their connector up and out of its socket on the power supply.
  • Pull the DC-Out cables straight up to lift their connector up and out of its socket on the power supply.

Yorum Ekle

Remove the two 7.6 mm Phillips screws securing the power supply to the lower case.
  • Remove the two 7.6 mm Phillips screws securing the power supply to the lower case.

Question: if a screw doesn't come out, what do you recommend, without potentially damaging the system, inside and out?

kramiz2488 - Yanıt

It seems these can be quite tight, but they did come loose with someextra force in my case. They did that thing where it makes cracking sounds, but nothing really breaks. They're just really tight in there. - I just wouldn't recommend taking these out too often.

Michael Hendriks - Yanıt

Lift the power supply upward from its left edge as viewed from the front of the PS3.
  • Lift the power supply upward from its left edge as viewed from the front of the PS3.

Yorum Ekle

Continue to lift the left edge of the power supply until it lifts off the two metal posts shown in the second picture. Remove the power supply from the PS3, minding any cables that may get caught.
  • Continue to lift the left edge of the power supply until it lifts off the two metal posts shown in the second picture.

  • Remove the power supply from the PS3, minding any cables that may get caught.

It seems it kind of ends for me here. I can only lift the left side about an inch and then the right side stays down like it’s stuck to something underneath. It feels like I’m bending something. Could something have melted underneath?… It's really stuck, I can't get it to come loose. And I can't see much shining a light into it either. - Any tips?…

Michael Hendriks - Yanıt

I had the same issue but was able to get it off. The right side (as per the above picture) has two long column like sections that actually goes into the machine. Took me a bit of wiggling and some brute force.

Ivan Amaro - Yanıt

Pull the fan cables upward to lift the fan connector up and out of its socket on the motherboard.
  • Pull the fan cables upward to lift the fan connector up and out of its socket on the motherboard.

Yorum Ekle

De-route the fan cables from under the plastic hook molded into the fan shroud.
  • De-route the fan cables from under the plastic hook molded into the fan shroud.

Yorum Ekle

Remove the two 9.5 mm Phillips screws securing the fan to the heat sink.
  • Remove the two 9.5 mm Phillips screws securing the fan to the heat sink.

Yorum Ekle

Lift the fan out of the heat sink, minding any cables that may get caught.
  • Lift the fan out of the heat sink, minding any cables that may get caught.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

37 başka kişi bu kılavuzu tamamladı.

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 6

Son 7 Gün: 64

Son 30 Gün: 300

Her zaman: 49,993