Ana içeriğe geç

Giriş

How to disassemble and change the Laser Unit.

Videoya Genel Bakış

  1. Turn off the console and disconnect all cables.
    • Turn off the console and disconnect all cables.

  2. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws.
    • You must remove the warranty sticker and 4 screws.

  3. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw.
    • After removing HDD bay cover, you will see another 3 screw.

  4. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel.
    • Push there to release and remove upper back bezel.

  5. MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now

    MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now
  6. The upper front bezel is harder to remove. The upper front bezel is harder to remove. The upper front bezel is harder to remove.
    • The upper front bezel is harder to remove.

  7. Remove 7 screws to release top cover. Remove 7 screws to release top cover. Remove 7 screws to release top cover.
    • Remove 7 screws to release top cover.

  8. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.
    • Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

  9. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable.
    • To release the laser unit disconnect this flex-cable.

  10. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel.
    • One flex-cable, for rubbers and the metal bezel.

  11. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.
    • Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

  12. Assembling, assembling... Assembling, assembling... Assembling, assembling...
    • Assembling, assembling...

  13. Let's test the device before fully assembling it. Let's test the device before fully assembling it.
    • Let's test the device before fully assembling it.

Sonuç

To reassemble your device, follow these instructions in reverse order.

10 farklı kişi bu kılavuzu tamamladı.

ZFix

Üyelik tarihi: 09-12-2013

164.069 İtibar

305 adet Kılavuz yazıldı

Takım

Master Techs Master Techs üyesi

Community

286 Üyeler

808 adet Kılavuz yazıldı

2 Yorum

Very good job, kudos!

Kevin Borras - Yanıt

I have found that there are to types of lasers do you sell the second one that does not have the black screws on top but are silver. I have found the one with the silver screws has a smaller laser flex cable and plug. its for the cech-43xx

jack blevinski - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 Gün: 11

Son 30 Gün: 84

Her zaman: 18,289