Eşyalarını Tamir Et Topluluk Mağaza

PlayStation 3 Super Slim Laser Unit Replacement

Yazan: ZFix (ve 5 başka katılımcı)
  • Yorumlar: 4
  • Favoriler: 20
  • Tamamlanma: 10

Zorluk

Orta

Adımlar

12

Gerekli Süre

Bir süre öner??

Bölümler

1

İşaretler

1

Member-Contributed Guide

Üye Katkılı Kılavuz

Topluluğumuzun müthiş bir üyesi bu kılavuzu hazırladı. Bu kılavuz, iFixit personeli tarafından yönetilmiyor.

Giriş

How to disassemble and change the Laser Unit.

Aletler

Parçalar

Hiçbir parça belirtilmedi.

Videoya Genel Bakış

  1. Turn off the console and disconnect all cables.

    • Turn off the console and disconnect all cables.

    Düzenle

  2. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws.

    • You must remove the warranty sticker and 4 screws.

    Düzenle

  3. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw.

    • After removing HDD bay cover, you will see another 3 screw.

    Düzenle

  4. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel.

    • Push there to release and remove upper back bezel.

    Düzenle

  6. The upper front bezel is harder to remove. The upper front bezel is harder to remove. The upper front bezel is harder to remove.

    • The upper front bezel is harder to remove.

    Düzenle

  7. Remove 7 screws to release top cover. Remove 7 screws to release top cover. Remove 7 screws to release top cover.

    • Remove 7 screws to release top cover.

    Düzenle

  8. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

    • Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

    Düzenle

  9. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable.

    • To release the laser unit disconnect this flex-cable.

    Düzenle

  10. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel.

    • One flex-cable, for rubbers and the metal bezel.

    Düzenle

  11. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

    • Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

    Düzenle

  12. Assembling, assembling... Assembling, assembling... Assembling, assembling...

    • Assembling, assembling...

    Düzenle

  13. Let's test the device before fully assembling it. Let's test the device before fully assembling it.

    • Let's test the device before fully assembling it.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

10 farklı kişi bu kılavuzu tamamladı.

Yazar

5 tane daha katılımcı ile

ZFix

Üyelik tarihi: 09-12-2013

184.314 İtibar

330 adet Kılavuz yazıldı

Rozetler: 35

+32 tane daha rozet

Takım

Master Techs Master Techs üyesi

Community

307 Üyeler

1.105 adet Kılavuz yazıldı

4 Yorum

Very good job, kudos!

Kevin Borras - Yanıt

I have found that there are to types of lasers do you sell the second one that does not have the black screws on top but are silver. I have found the one with the silver screws has a smaller laser flex cable and plug. its for the cech-43xx

jack blevinski - Yanıt

My only problem now is how to purchase the right Laser unit? Any specs for the right Laser unit? Thanks

Sebasttain Tuscano - Yanıt

I’ve done this but my ps3 still doesn’t read disks it spins it up 4 odd times but doesn’t read them and it sounds like the disk skims the top of the laser unit but it hasn't done any damage and it does it with both units, I’m so lost on what to do.

Dome Bucket - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 4

Son 7 gün: 9

Son 30 gün: 60

Her zaman: 21,585