Eşyalarını Tamir Et Topluluk Mağaza

Power Mac G4 M5183 Logic Board Replacement

Giriş

This guide will show you how to remove the PowerMac logic board.

Neye ihtiyacın var

  1. Power Mac G4 M5183 Logic Board Replacement, Opening PowerMac G4 M5183 Case: adım 1, 2 resimden 1. Power Mac G4 M5183 Logic Board Replacement, Opening PowerMac G4 M5183 Case: adım 1, 2 resimden 2.

    • Pull on outer latch.

    • Lower door until it is level with your work surface.

    • Before working on the computer make sure it is not plugged into a power supply, then touch a metal object. This discharges static electricity, which could damage the computer.

    Düzenle

  2. Power Mac G4 M5183 Logic Board Replacement, Heat Sink: adım 2, 2 resimden 1. Power Mac G4 M5183 Logic Board Replacement, Heat Sink: adım 2, 2 resimden 2.

    • Use the spudger to pry the clips horizontally off of the heat sink.

    • Fully remove the clips by lifting upwards.

    Düzenle

  3. Power Mac G4 M5183 Logic Board Replacement: adım 3, 1 resimden 1.

    • Remove the heat sink by pulling upwards, off of the logic board.

    Düzenle

  5. Power Mac G4 M5183 Logic Board Replacement, RAM: adım 4, 2 resimden 1. Power Mac G4 M5183 Logic Board Replacement, RAM: adım 4, 2 resimden 2.

    • Locate the RAM modules.

    • Pull side tabs outward. The RAM will pop out of the housing.

    Düzenle

  6. Power Mac G4 M5183 Logic Board Replacement, Graphics Card: adım 5, 2 resimden 1. Power Mac G4 M5183 Logic Board Replacement, Graphics Card: adım 5, 2 resimden 2.

    • Remove the single screw with the Phillips #1 screwdriver.

    • Pull the graphics card up and out.

    Düzenle

  7. Power Mac G4 M5183 Logic Board Replacement, Logic Board: adım 6, 2 resimden 1. Power Mac G4 M5183 Logic Board Replacement, Logic Board: adım 6, 2 resimden 2.

    • Remove the six indicated cables attached to the logic board.

    • Use the spudger to remove the modem cable as indicated.

    Düzenle

  8. Power Mac G4 M5183 Logic Board Replacement: adım 7, 2 resimden 1. Power Mac G4 M5183 Logic Board Replacement: adım 7, 2 resimden 2.

    • Unfasten 3 Phillips screws revealed beneath the heat sink on the CPU board.

    • Carefully remove the CPU board from the Mother Board.

    • Remove the barrell nut screws from the Mother Board which held the CPU board.

    • Unfasten 3 Phillips #1 screws on Mother Board as shown in illustration 1.

    • Slide the logic board about a quarter of an inch to free it from the three retaining pins.

    • Pull upwards and outwards to fully remove the logic board.

    Düzenle

  9. Power Mac G4 M5183 Logic Board Replacement: adım 8, 1 resimden 1.

    • After removing the (3) #2 philips screws, remove the (4) 1/4" hex nuts, then slide as directed and remove board.

    Düzenle
Bitiş Çizgisi

15 farklı kişi bu kılavuzu tamamladı.

Yazar

7 tane daha katılımcı ile

Justin Petrilli

Üyelik tarihi: 01/21/10

3.114 İtibar

11 adet Kılavuz yazıldı

Rozetler: 14

+11 tane daha rozet

Ekip

Cal Poly, Team 13-24, Maness Winter 2010 Cal Poly, Team 13-24, Maness Winter 2010 üyesi

CPSU-MANESS-W10S13G24

4 Üyeler

25 adet Kılavuz yazıldı

3 Yorum

Are the "hex nuts" under the processor board? Could you provide a close up picture of the "nuts?"

D george - Yanıt

So what is being replaced here? Wouldn’t one have to purchase a new logic board? Any info would be greatly appreciated!

Sandra Cai - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 gün: 8

Son 30 gün: 29

Her zaman: 17,883