/
Tezgahım

Cihazların için kılavuz, parça ve yanıtlara hızlı erişim edin

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Üye Ol
Giriş Yap
Dünyanın en büyük onarım topluluğuna katılın
Power Mac G4 Quicksilver Logic Board Replacement

Power Mac G4 Quicksilver Logic Board Replacement

Cameron Christensen

Cameron Christensen ve 4 diğer katkıda bulunanlar

En son February 19, 2016 tarihinde güncellendi

15 - 30 dakika
Orta

Giriş

1. adıma git

Removing the mother board of the Power Mac G4 Quicksilver.

Neye ihtiyacın var

Aletler

  1. Power Mac G4 Quicksilver Logic Board Replacement, Opening the case: adım 1, 1 resimden 1.

    • The handle to open your computer is located on top of the right side panel.

    Düzenle

  2. Power Mac G4 Quicksilver Logic Board Replacement: adım 2, 2 resimden 1. Power Mac G4 Quicksilver Logic Board Replacement: adım 2, 2 resimden 2.

    • Grab the circular handle and pull outward.

    Düzenle

  3. Power Mac G4 Quicksilver Logic Board Replacement: adım 3, 1 resimden 1.

    • Your computer is now open and ready for repair.

    Düzenle

  4. Power Mac G4 Quicksilver Logic Board Replacement, Video Adapter: adım 4, 1 resimden 1.

    • This is your Power Mac G4's video adapter.

    Düzenle

  6. Power Mac G4 Quicksilver Logic Board Replacement: adım 5, 1 resimden 1.

    • Start by removing the screw holding the card to the chassis as shown.

    Düzenle

  7. Power Mac G4 Quicksilver Logic Board Replacement: adım 6, 1 resimden 1.

    • Before lifting the card out, this small plastic tab needs to be pulled back there by releasing it entirely.

    Düzenle

  8. Power Mac G4 Quicksilver Logic Board Replacement: adım 7, 2 resimden 1. Power Mac G4 Quicksilver Logic Board Replacement: adım 7, 2 resimden 2.

    • With the tab and screw removed, lift the card straight out.

    • When putting the card back in, take care to apply even pressure across the top with your thumbs. This will avoid damaging the card.

    Düzenle

  9. Power Mac G4 Quicksilver Logic Board Replacement, Logic Board: adım 8, 1 resimden 1.

    • Disconnect both the power cables and IDE cable from the mother board.

    Düzenle

  10. Power Mac G4 Quicksilver Logic Board Replacement: adım 9, 1 resimden 1.

    • Remove these three screws that hold the motherboard fan and modem connector to the chassis.

    Düzenle

  11. Power Mac G4 Quicksilver Logic Board Replacement: adım 10, 1 resimden 1.

    • Remove the four screws shown to free the mother board from the chassis.

    Düzenle

  12. Power Mac G4 Quicksilver Logic Board Replacement: adım 11, 3 resimden 1. Power Mac G4 Quicksilver Logic Board Replacement: adım 11, 3 resimden 2. Power Mac G4 Quicksilver Logic Board Replacement: adım 11, 3 resimden 3.

    • Lift the fan shroud and fan straight up and out. Take care to disconnect the indicated connector

    • Remove the heatsink clamps with a flathead screwdriver and do the same for the other side.

    • Lift off the heatsink and remove the 4 screws of the CPU board.

    • There are 4 pins: remove the 3 pins near the RAM but not the pin nearest You.

    • You are now ready to slide gently (and without ANY difficult) the motherboard. Lift up and the game is done.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

10 farklı kişi bu kılavuzu tamamladı.

Yazar

4 tane daha katılımcı ile

Cameron Christensen

Üyelik tarihi: 01/20/10

590 İtibar

3 adet Kılavuz yazıldı

Rozetler: 12

+9 tane daha rozet

Ekip

Cal Poly, Team 14-41, Regan Winter 2010 Cal Poly, Team 14-41, Regan Winter 2010 üyesi

CPSU-REGAN-W10S14G41

4 Üyeler

17 adet Kılavuz yazıldı

0Kılavuz Yorumları

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 6

Son 30 gün: 39

Her zaman: 17,220