Eşyalarını Tamir Et Topluluk Mağaza

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

RCA Voyager II RCT6773W22 Disassembly

Giriş

Taking apart the RCA Voyager II is pretty straightforward. Here is a short Guide.

Note that the tablet pictured has been disassembled and reassembled before.

Neye ihtiyacın var

  1. RCA Voyager II RCT6773W22 Disassembly, RCA Voyager II RCT6773W22 Disassembly: adım 1, 1 resimden 1.

    • Have Workstation Prepped

    Düzenle

  2. RCA Voyager II RCT6773W22 Disassembly: adım 2, 1 resimden 1.

    • remove the two screws on the top of the device with a PH000 screwdriver

    Düzenle

  3. RCA Voyager II RCT6773W22 Disassembly: adım 3, 1 resimden 1.

    • Starting from the top, place pick or plastic tool between the power button and screen edge and push apart slightly.

    Düzenle

  4. RCA Voyager II RCT6773W22 Disassembly: adım 4, 1 resimden 1.

    • Run pick across the top to the right and then down the right side and around the rest of the tablet.

    • There is a good amount of space between the bezel and the board. Be gentle, but the risk of breaking components is low.

    Düzenle

  5. RCA Voyager II RCT6773W22 Disassembly: adım 5, 2 resimden 1. RCA Voyager II RCT6773W22 Disassembly: adım 5, 2 resimden 2.

    • lift section out of the black casing from the bottom, lift and remove by pulling away from tablet.

    Düzenle

  6. RCA Voyager II RCT6773W22 Disassembly: adım 6, 1 resimden 1.

    • Battery connection (on older models, may be soldered to board)

    • Front Camera

    • Digitizer

    • LCD

    • Speaker

    Düzenle

  8. RCA Voyager II RCT6773W22 Disassembly: adım 7, 1 resimden 1.

    • Remove battery Connection First

    • Do not use any metal tools while the battery is plugged in. It may cause a short.

    Düzenle

  9. RCA Voyager II RCT6773W22 Disassembly: adım 8, 1 resimden 1.

    • unplug the speaker

    Düzenle

  10. RCA Voyager II RCT6773W22 Disassembly: adım 9, 3 resimden 1. RCA Voyager II RCT6773W22 Disassembly: adım 9, 3 resimden 2. RCA Voyager II RCT6773W22 Disassembly: adım 9, 3 resimden 3.

    • Lift the black cover over all three flex cables (Camera, LCD, Digitizer) with a plastic tool.

    • The covers are incredibly fragile, and easy to break

    • gently disconnect all three cables with your fingers by pulling slightly

    Düzenle

  11. RCA Voyager II RCT6773W22 Disassembly: adım 10, 1 resimden 1.

    • remove the three screws securing the board with your PH000 Screwdriver

    Düzenle

  12. RCA Voyager II RCT6773W22 Disassembly: adım 11, 2 resimden 1. RCA Voyager II RCT6773W22 Disassembly: adım 11, 2 resimden 2.

    • lift the board out gently

    • Do not tug the board out too hard, the antenna cable on the left is soldered in!

    • Fold board over the left side of the tablet and gently remove tape securing antenna to the case. Use a small amount of heat if necessary.

    Düzenle

  13. RCA Voyager II RCT6773W22 Disassembly: adım 12, 2 resimden 1. RCA Voyager II RCT6773W22 Disassembly: adım 12, 2 resimden 2.

    • remove tape from top and bottom of the battery.

    • with a plastic piece, lift battery from adhesive securing it in place.

    • do not use a metal or sharp tool to remove the battery, tearing or puncturing it may cause it to explode or heat rapidly, and may damage your device.

    • The battery is secured directly to the back of the LCD. Exercise caution while removing the battery not to damage the LCD.

    • The battery is soft and somewhat malleable - it can bend slightly without damage.

    Düzenle

  14. RCA Voyager II RCT6773W22 Disassembly: adım 13, 2 resimden 1. RCA Voyager II RCT6773W22 Disassembly: adım 13, 2 resimden 2.

    • Place picks between the lcd and the plastic clips holding it in place.

    • The pick placement to the top left side (near the power button) is smaller and on a corner. I recommend inserting this pick last.

    Düzenle

  15. RCA Voyager II RCT6773W22 Disassembly: adım 14, 1 resimden 1.

    • Gently push top right pick down to lift LCD from the clip. Run across the top and right side to further lift LCD.

    • Use picks as needed to separate LCD in other areas.

    Düzenle

  16. RCA Voyager II RCT6773W22 Disassembly: adım 15, 1 resimden 1.

    • Once separated and loose, remove picks so you do not damage the LCD while removing it.

    • To remove, lift top of LCD and pull out of case away from the speaker, which is fixed to the digitizer frame.

    Düzenle

  17. RCA Voyager II RCT6773W22 Disassembly: adım 16, 2 resimden 1. RCA Voyager II RCT6773W22 Disassembly: adım 16, 2 resimden 2.

    • to remove Digitizer/Glass from the frame and speaker, slide a pick under a corner between the glass and frame to loosen adhesive

    • If you're having issues loosening the adhesive, use a heat gun around the edges, then try again.

    Düzenle

  18. RCA Voyager II RCT6773W22 Disassembly: adım 17, 1 resimden 1.

    • You have completely dismantled the RCA Voyager II

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

35 farklı kişi bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

Chris

Üyelik tarihi: 01/11/16

2.025 İtibar

1 Kılavuz yazıldı

Rozetler: 13

+10 tane daha rozet

31 Yorum

what is that flat part that has the little copper bar in the middle. What do you call that?

TheUnchanted Sword - Yanıt

The LCD has a piece of copper tape on it, is that what you mean?

Sam Goldheart -

Nice Guide. Very Simple and Easy to follow!

Aerial L - Yanıt

Bonne site merci pour tous je suis très heureux content que entrer dans ce site

diego jamal - Yanıt

Anyone know which company made this very fragile digitizer for RCA Voyager?

Spock Chen - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 15

Son 30 gün: 32

Her zaman: 21,580