Giriş

In order to perform any sort of repair on the throttle body unit, it must first be removed from the engine by following these step by step instructions

Parçalar

Hiçbir parçaya gerek yok.

Firstly Disconnect  battery Always take the negative terminal off first.
  • Firstly Disconnect battery

    • Always take the negative terminal off first.

    • '''General Tip After disconnecting the battery leave the car for about 10 mins , This lets any residual energy left in the electrical system to dissapate. It is good practise whatever the job

Yorum Ekle

Locate throttle body on right side of engine, it is between the intake tube and intake manifold.
  • Locate throttle body on right side of engine, it is between the intake tube and intake manifold.

Yorum Ekle

Locate throttle linkage cable assembly.
  • Locate throttle linkage cable assembly.

Yorum Ekle

Twist the assembly clockwise. Twist the assembly clockwise.
  • Twist the assembly clockwise.

Yorum Ekle

Slide both slackened cables off assembly’s guides.
  • Slide both slackened cables off assembly’s guides.

Yorum Ekle

Locate the two hoses on the top of the throttle body. Gently lift the hoses off.
  • Locate the two hoses on the top of the throttle body.

  • Gently lift the hoses off.

Yorum Ekle

Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.
  • Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.

Yorum Ekle

Remove the intake tube from the throttle body.
  • Remove the intake tube from the throttle body.

Yorum Ekle

Locate wiring clip on the underside of the throttle body.
  • Locate wiring clip on the underside of the throttle body.

Yorum Ekle

Press down on the locking mechanism before gently removing the wiring clip. Press down on the locking mechanism before gently removing the wiring clip.
  • Press down on the locking mechanism before gently removing the wiring clip.

Yorum Ekle

Locate throttle linkage arm. Open the locking clip with a flat head screwdriver. Pry off the linkage arm with a flat head screwdriver.
  • Locate throttle linkage arm.

  • Open the locking clip with a flat head screwdriver.

  • Pry off the linkage arm with a flat head screwdriver.

Yorum Ekle

Locate the three 13mm nuts attaching the throttle body to the intake manifold. Remove nuts with a 13mm crescent wrench. Remove nuts with a 13mm crescent wrench.
  • Locate the three 13mm nuts attaching the throttle body to the intake manifold.

  • Remove nuts with a 13mm crescent wrench.

Yorum Ekle

Lift the throttle body off of the intake manifold.
  • Lift the throttle body off of the intake manifold.

  • The manifold is now out of the engine bay and ready for cleaning or adjustment.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Raymond

Üyelik tarihi: 11-10-2010

61 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 3-28, Regan Fall 2010 Cal Poly, Team 3-28, Regan Fall 2010 üyesi

CPSU-REGAN-F10S3G28

4 Üyeler

9 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 Gün: 1

Son 30 Gün: 10

Her zaman: 3,571