Ana içeriğe geç

Giriş

This guide will show you how to remove the power supply on your HP Compaq dx2000MT.

  1. Turn off your computer and remove the power cable by pulling it straight out of its socket.
    • Turn off your computer and remove the power cable by pulling it straight out of its socket.

  2. Remove the two Phillips #2 screws that secure the case door to the device. Remove the two Phillips #2 screws that secure the case door to the device.
    • Remove the two Phillips #2 screws that secure the case door to the device.

  3. Remove the side case door by pushing towards the rear of the device with your hand. This may take considerable force so keep pushing! Once you slide the door back, remove it by pulling it outwards from the device.
    • Remove the side case door by pushing towards the rear of the device with your hand.

    • This may take considerable force so keep pushing!

    • Once you slide the door back, remove it by pulling it outwards from the device.

  4. MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now

    MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now
  5. Remove the side case door by pushing towards the rear of the device with your hand. Once again, this may take considerable force. Once you slide the door back, remove it by pulling it outwards from the device.
    • Remove the side case door by pushing towards the rear of the device with your hand.

    • Once again, this may take considerable force.

    • Once you slide the door back, remove it by pulling it outwards from the device.

  6. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.
    • Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

  7. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.
    • Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

  8. Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply
    • Remove the 4 Torx T15 screws from the rear of the power supply

  9. Slide the power supply towards the front of the device Keep your hand underneath it! You don't want to drop it!
    • Slide the power supply towards the front of the device

    • Keep your hand underneath it! You don't want to drop it!

    • Then pull the power supply down and remove it from the case.

Sonuç

To reassemble your device, follow these instructions in reverse order.

7 farklı kişi bu kılavuzu tamamladı.

Logan Pace

Üyelik tarihi: 12-10-2011

2.020 İtibar

9 adet Kılavuz yazıldı

Takım

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011 üyesi

CPSU-REGAN-F11S17G16

4 Üyeler

17 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 6

Her zaman: 2,503