Giriş

This guide instructs you in the removal of the side panel of your Canon Optura 100MC. This disassembly is a prerequisite to many other internal repairs, such as buttons and speaker.

Parçalar

Hiçbir parçaya gerek yok.

Orient the camera with the hand strap facing you.
  • Orient the camera with the hand strap facing you.

  • Remove the two 4mm #00 Philips screws.

  • When the screws are removed, the black plate will easily come off as well as the two metal plates under it. Be careful to not let them fall or get lost.

Yorum Ekle

Lift the strap up.
  • Lift the strap up.

Yorum Ekle

  • Orient the camera so that the back button panel and viewfinder are facing you.

  • Push the "Battery Release" button to the side and hold.

Yorum Ekle

  • While holding the battery release button to the side, slide the battery towards you, past the release button.

Yorum Ekle

  • Orient the camera so that the viewfinder is on your left and the lens is on your right.

  • Remove the 4mm #00 Phillips screw.

Yorum Ekle

  • Reorient the camera with the back button pad and viewfinder towards you.

  • Remove the three 4mm #00 Phillips screws shown on the rear face of camcorder.

Yorum Ekle

  • Remove the plastic cover from the rear of the camcorder by gently pulling it towards you while holding the camera as shown.

  • The Battery Should be removed at this point, please ignore it in the picture.

Yorum Ekle

  • Remove the 4mm #00 Phillips screw located to the right of the LCD release switch.

Yorum Ekle

  • Open the LCD by using the release switch.

  • Reorient the camera with the playback button pad and edge of LCD screen facing you.

  • Remove the 4mm #00 Phillips screw shown.

Yorum Ekle

  • Reorient the camera with the top facing you. The side with the LCD screen should be on the right and the other side panel should be on the right.

  • Open the pop up flash on the top of the camcorder.

  • A loud clicking noise is expected.

  • Remove the 4mm #00 Phillips screw shown.

Yorum Ekle

  • Reorient the camera with the bottom facing you, LCD screen on the right, side panel on the left.

  • Open the tape deck by sliding the switch and moving the deck cover to the left as shown.

Yorum Ekle

  • Remove 4mm #00 Phillips screw.

Yorum Ekle

  • Reorient camera with lens facing you.

  • Remove the #00 Philips 4mm screw shown on the hinge of the tape deck cover.

Yorum Ekle

  • To remove the camcorder lens hood, twist the hood to counterclockwise and it will come loose, then pull towards you.

Yorum Ekle

  • Close the tape deck by gently pushing it toward the body of the camera.

  • Slide and remove the plastic cover on the bottom right, exposing the interface shown.

Yorum Ekle

  • Gently pull the front plastic cover towards you to remove.

Yorum Ekle

  • Remove 2 Philips #00 4mm screw shown.

Yorum Ekle

  • Reorient the camera so you are looking at the side of the camera with the viewfinder on the left and lens on the right.

  • Holding the camera as shown,remove the 4mm #00 Phillips screw.

Yorum Ekle

  • Remove the 4 Philips #00 4mm screws shown.

Yorum Ekle

  • Reorient the camera with the lens facing you.

  • Gently pull the side panel of the camera to the right to remove.

  • Be aware that that there are wires connecting the cover to the body of the device, so the side cover will not come off entirely.

Yorum Ekle

  • The side of the device should now be open as shown. Again, there are wire connections between the side cover and the body of the camcorder. Do not separate the two entirely!

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Jeanette Neethling

Üyelik tarihi: 19-01-2011

531 İtibar

5 adet Kılavuz yazıldı

Takım

Cal Poly, Team 1-12, Amido Winter 2011 Cal Poly, Team 1-12, Amido Winter 2011 üyesi

CPSU-AMIDO-W11S1G12

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 0

Her zaman: 665