Eşyalarını Tamir Et Topluluk Mağaza

Repairing Black and Decker BL3000S Power Cord

Neye ihtiyacın var

  1. Repairing Black and Decker BL3000S Power Cord, Blender Base: adım 1, 2 resimden 1. Repairing Black and Decker BL3000S Power Cord, Blender Base: adım 1, 2 resimden 2.

    • Before disassembling the blender base, make sure the blender disconnected from any power outlet.

    • Lift the jar straight up from the base without tilting the jar.

    Düzenle

  2. Repairing Black and Decker BL3000S Power Cord: adım 2, 1 resimden 1.

    • Remove the top three 1/4 inch base screws using a Philip's head screwdriver.

    Düzenle

  3. Repairing Black and Decker BL3000S Power Cord: adım 3, 2 resimden 1. Repairing Black and Decker BL3000S Power Cord: adım 3, 2 resimden 2.

    • Remove the two base leg covers next to the power cord using pliers or a flat-head screwdriver.

    • This provides access to the base screws beneath.

    Düzenle

  5. Repairing Black and Decker BL3000S Power Cord: adım 4, 1 resimden 1.

    • Remove the following screws that secure the top and bottom halves of the base.

    • One 1/4 Phillips screw

    • One TA-20 screw

    • Both screwdrivers must have a minimum of a three inch shank (length).

    • Screwdrivers with extenders will not fit down the access holes.

    Düzenle

  6. Repairing Black and Decker BL3000S Power Cord: adım 5, 1 resimden 1.

    • Lift the top half of the base from the bottom half of the base to reveal the internal mechanism.

    Düzenle

  7. Repairing Black and Decker BL3000S Power Cord, Power Cord: adım 6, 1 resimden 1.

    • Tug on wires in the marked locations to make sure they are secure.

    • If the wire stays still, the connection is secure.

    • If you still have problems with the blender, it is probably a problem with the motor. Since the motor is irreplaceable, you will have to order a new blender.

    Düzenle

  8. Repairing Black and Decker BL3000S Power Cord: adım 7, 1 resimden 1.

    • If the wire comes off, the connection is insecure. You will need to solder the connection to make it solid again.

    • If you don't know how to solder, here is a link to show you how. http://www.aaroncake.net/electronics/sol...

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

Elmer Pres Urbano

Üyelik tarihi: 10/05/12

148 İtibar

1 Kılavuz yazıldı

Rozetler: 9

+6 tane daha rozet

Ekip

Cal Poly, Team 6-34, Regan Fall 2012 Cal Poly, Team 6-34, Regan Fall 2012 üyesi

CPSU-REGAN-F12S6G34

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 9

Son 30 gün: 36

Her zaman: 3,878