Giriş

How to remove and replace the hard drive.

Remove the 7 mm Philip screws.
  • Remove the 7 mm Philip screws.

  • Remove the 10 mm Philip screws.

  • Remove the 14 mm Philip screw.

Yorum Ekle

Open the flap on the left hand side. Open the flap on the left hand side.
  • Open the flap on the left hand side.

Yorum Ekle

Insert the iPod opening tools between the right and left sides of the latch. Pry the right side  of the latch, and then pry the left side to detach the laptop's cover.
  • Insert the iPod opening tools between the right and left sides of the latch.

  • Pry the right side of the latch, and then pry the left side to detach the laptop's cover.

Yorum Ekle

Open the flap on the right side. Open the flap on the right side.
  • Open the flap on the right side.

Yorum Ekle

Insert the iPod opening tools towards the right side of the latch.
  • Insert the iPod opening tools towards the right side of the latch.

  • Gently pry the right side out to release the top cover.

Yorum Ekle

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Lift the keyboard slowly. A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.
  • Lift the keyboard slowly.

  • A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.

Yorum Ekle

Use your fingers or a spudger to detach the connector.
  • Use your fingers or a spudger to detach the connector.

Yorum Ekle

Carefully lift and remove the keyboard. Carefully lift and remove the keyboard.
  • Carefully lift and remove the keyboard.

Yorum Ekle

On the back of the computer, use a Flathead screwdriver to remove this lone screw.
  • On the back of the computer, use a Flathead screwdriver to remove this lone screw.

Yorum Ekle

After the screw is out, gently remove the cover. After the screw is out, gently remove the cover.
  • After the screw is out, gently remove the cover.

Yorum Ekle

Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.
  • Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.

Yorum Ekle

Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.
  • Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.

Yorum Ekle

Remove the final two screws (shown) and slide out the hard drive. Remove the final two screws (shown) and slide out the hard drive.
  • Remove the final two screws (shown) and slide out the hard drive.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 başka kişi bu kılavuzu tamamladı.

Derek Driscoll

Üyelik tarihi: 15-04-2010

110 İtibar

16 adet Kılavuz yazıldı

Takım

Cal Poly, Team 26-27, Regan Spring 2010 Cal Poly, Team 26-27, Regan Spring 2010 üyesi

CPSU-REGAN-S10S26G27

3 Üyeler

18 adet Kılavuz yazıldı

Bir Yorum

You don't have to go to this length to remove the hard drive on a 560Z. Only do steps 0 (remove battery), 9 (remove screw) and 10 (remove cover). Then simply grab the blue tab of the hard drive caddy and pull the drive out of the bay. Complete directions on maintenance of the IBM Thinkpad 560Z can be found here:

http://www.thinkpads.com/support/hmm/hmm...

The Hardware Maintenance Manual has all of the information you need to take a 560Z apart and put it back together.

The procedure outlined here is similar to what the 560, 560E and 560X systems required; the 560Z is totally different when removing the hard drive.

Raymond - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 13

Her zaman: 2,465