Ana içeriğe geç

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

Rival Mini Chopper MC-67BL Power Cord Replacement

Neye ihtiyacın var

  1. Rival Mini Chopper MC-67BL Power Cord Replacement, Turning Gears: adım 1, 2 resimden 1. Rival Mini Chopper MC-67BL Power Cord Replacement, Turning Gears: adım 1, 2 resimden 2.
    • Twist the plastic lid counterclockwise to unlock it.

    • Lift the lid to remove it from the container.

  2. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 2, 1 resimden 1.
    • Carefully remove the blade from the container.

    • For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

  3. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 3, 1 resimden 1.
    • With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

  4. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 4, 1 resimden 1.
    • Use your fingers to pry out the two rubber feet from the bottom cover of the base.

    • The two feet furthest from the button tower contain screws. The other two feet do not.

  5. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 5, 2 resimden 1. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 5, 2 resimden 2.
    • Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

    • Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

  6. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 6, 1 resimden 1.
    • Firmly lift the bottom cover off of the base.

  7. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 7, 1 resimden 1.
    • Remove the smaller white gear by lifting it up with your hand.

  8. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 8, 3 resimden 1. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 8, 3 resimden 2. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 8, 3 resimden 3.
    • Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

    • Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

    • Continue turning the gear until completely removed from the blade-shaft.

  9. Rival Mini Chopper MC-67BL Power Cord Replacement, Power Cord: adım 9, 1 resimden 1.
    • Use your hand to firmly pull the blade-shaft from the base.

  10. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 10, 1 resimden 1.
    • Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

  11. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 11, 1 resimden 1.
    • Unwind power cord from the base pegs.

  12. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 12, 2 resimden 1. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 12, 2 resimden 2.
    • Use the plastic opening tool to pry open the base from the main body.

    • These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.

    • Once freed, lift the base panel from the main body. The motor and power cable are connected to this panel.

  13. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 13, 1 resimden 1.
    • Pull the power cord wires up from underneath the wire hook on the side of the motor.

  14. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 14, 2 resimden 1. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 14, 2 resimden 2.
    • Carefully cut into black wire casing for both wires using a small knife and peel away the black casing.

    • Only cut deep enough to remove the casing.

    • For reassembly you will need black electrical tape to keep the wires from being exposed.

  15. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 15, 1 resimden 1.
    • Using a soldering kit, remove the solder for the black power cord from the circuit board.

    • Follow this soldering guide if you need extra help!

  16. Rival Mini Chopper MC-67BL Power Cord Replacement: adım 16, 1 resimden 1.
    • Use a small knife to cut the copper wires from the bracket holding the black wire and power cord together.

    • For reassembly the copper wires will need to be soldered together.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Roxanne

Üyelik tarihi: 10/17/13

522 İtibar

4 adet Kılavuz yazıldı

Ekip

Cal Poly, Team 4-29, Amido Fall 2013 Cal Poly, Team 4-29, Amido Fall 2013 üyesi

CPSU-AMIDO-F13S4G29

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 3

Her zaman: 370