Ana içeriğe geç

RotoZip Rebel REB01 Type 2 Power Cord Replacement

Neye ihtiyacın var

  1. RotoZip Rebel REB01 Type 2 Power Cord Replacement, Saw Casing: adım 1, 1 resimden 1.
    • Unplug the saw before attempting any of the replacement guides.

    • Orient the saw so that the handle is closest to you and the saw end points towards the left.

  2. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 2, 2 resimden 1. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 2, 2 resimden 2.
    • Push down on the grey lock on the right side of the handle to unlock it.

    • Pull the handle to detach it from the saw.

  3. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 3, 2 resimden 1. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 3, 2 resimden 2.
    • Lift the black lock at the tip of the saw to unlock the depth gauge.

    • Pull the depth gauge to detach it from the saw.

  4. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 4, 1 resimden 1.
    • Rotate the device so that the bottom of the saw is facing upwards.

    • Remove the six 20mm screws with a 6mm flathead screwdriver.

  5. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 5, 2 resimden 1. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 5, 2 resimden 2.
    • Cut through the stickers on the right and left sides of the saw using a metal spudger.

    • Pull off the top half of the casing.

  6. RotoZip Rebel REB01 Type 2 Power Cord Replacement, Power Cord: adım 6, 2 resimden 1. RotoZip Rebel REB01 Type 2 Power Cord Replacement, Power Cord: adım 6, 2 resimden 2.
    • Remove the two 14 mm screws on the plastic plate holding the power cord with a flat head screwdriver.

    • Lift off the plastic plate holding the power cord with a tweezer.

  7. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 7, 1 resimden 1.
    • Pull the switchboard out slowly.

    • The power switch will also come out. Set it on the side.

  8. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 8, 2 resimden 1. RotoZip Rebel REB01 Type 2 Power Cord Replacement: adım 8, 2 resimden 2.
    • Pinch the two white clips with your thumb while simultaneously removing the black and white wires.

    • Remove the power cord from the saw.

    • When reassembling, make sure to plug the black wire into the top clip.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Ezzeddeen Gazali

Üyelik tarihi: 10/06/16

81 İtibar

1 Kılavuz yazıldı

Ekip

Cal Poly, Team 4-4, Livingston Fall 2016 Cal Poly, Team 4-4, Livingston Fall 2016 üyesi

CPSU-LIVINGSTON-F16S4G4

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 9

Son 30 gün: 15

Her zaman: 608