Eşyalarını Tamir Et Topluluk Mağaza

Ryobi RS290G Motor Replacement

Giriş

Use this guide to help replace the Ryobi RS290G Sander motor. The Ryobi RS290G uses a 2.6 AMP motor and 12,500 OPM (orbits per minute).

If you ordered the correct part, it should have the disconnect terminals already installed/crimped on.

Through out its use the motor may experience some damage, be faulty, and can eventually become unusable all together. With this guide, it can teach you how to salvage your Ryobi RS290G Sander and completely replace its old motor.

This is a pretty simple replacement and does not require much specialty skills. Have fun with it and enjoy your Ryobi RS290G sander.

Neye ihtiyacın var

  1. Ryobi RS290G Motor Replacement, Top Cap: adım 1, 1 resimden 1.

    • Remove two 20mm and one 16mm Phillips #2 screws from the housing assembly and exhaust port.

    Düzenle

  2. Ryobi RS290G Motor Replacement: adım 2, 1 resimden 1.

    • Remove the three 16mm Phillips #2 screws from the top cap/upper grip.

    Düzenle

  3. Ryobi RS290G Motor Replacement: adım 3, 1 resimden 1.

    • Remove the top cap.

    Düzenle

  4. Ryobi RS290G Motor Replacement, Switch Trigger: adım 4, 1 resimden 1.

    • Remove the switch trigger.

    Düzenle

  5. Ryobi RS290G Motor Replacement, Motor: adım 5, 1 resimden 1.

    • Remove the two 16mm Phillips #2 screws from the inner housing assembly.

    Düzenle

  7. Ryobi RS290G Motor Replacement: adım 6, 1 resimden 1.

    • Remove the two 14mm Phillips #2 screws from the cord clamp.

    Düzenle

  8. Ryobi RS290G Motor Replacement: adım 7, 2 resimden 1. Ryobi RS290G Motor Replacement: adım 7, 2 resimden 2.

    • Slide the power switch out of the housing assembly.

    Düzenle

  9. Ryobi RS290G Motor Replacement: adım 8, 1 resimden 1.

    • Carefully slide the housing assembly apart, avoiding damage or pulling on wires.

    Düzenle

  10. Ryobi RS290G Motor Replacement: adım 9, 2 resimden 1. Ryobi RS290G Motor Replacement: adım 9, 2 resimden 2.

    • Slide off the disconnect terminal for the switch (red lead) from the power switch using the flat end of a spudger.

    Düzenle

  11. Ryobi RS290G Motor Replacement: adım 10, 2 resimden 1. Ryobi RS290G Motor Replacement: adım 10, 2 resimden 2.

    • Slide out the brush assembly with the black lead from the inner housing assembly.

    Düzenle

  12. Ryobi RS290G Motor Replacement: adım 11, 1 resimden 1.

    • Slide off the disconnect terminal for the brush assembly (black lead) from the brush assembly.

    • You may need an ESD-safe flat edge tool, such as a spudger, to help slide off the disconnect terminal. Be careful not to damage the pieces or yourself.

    Düzenle

  13. Ryobi RS290G Motor Replacement: adım 12, 1 resimden 1.

    • Remove the armature assembly, with the motor, out of the inner housing assembly.

    Düzenle

  14. Ryobi RS290G Motor Replacement: adım 13, 3 resimden 1. Ryobi RS290G Motor Replacement: adım 13, 3 resimden 2. Ryobi RS290G Motor Replacement: adım 13, 3 resimden 3.

    • Replace the motor (also known as field assembly).

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 6

Her zaman: 903