Eşyalarını Tamir Et Topluluk Mağaza

SG 552-1 Commando Barrel Replacement

Giriş

This guide will be showing step-by-step instructions on how to get to and replace the barrel of the airsoft gun.

Neye ihtiyacın var

  1. SG 552-1 Commando Barrel Replacement, Barrel: adım 1, 2 resimden 1. SG 552-1 Commando Barrel Replacement, Barrel: adım 1, 2 resimden 2.

    • Using a flathead screwdriver, remove the pin holding the hand guard in place.

    • To remove this, turn the pin clockwise and push it through at the same time.

    • Pull the hand guard off.

    Düzenle

  2. SG 552-1 Commando Barrel Replacement: adım 2, 2 resimden 1. SG 552-1 Commando Barrel Replacement: adım 2, 2 resimden 2.

    • Using a Phillips #1 screwdriver, remove the two 8mm screws above the hand guard on both sides of the gun. There should be four total.

    Düzenle

  3. SG 552-1 Commando Barrel Replacement: adım 3, 2 resimden 1. SG 552-1 Commando Barrel Replacement: adım 3, 2 resimden 2.

    • Locate the button to fold over the folding stock and fold over the folding stock.

    • Using a Phillips #1 screwdriver, remove the 20mm screw located behind the folding stock.

    Düzenle

  5. SG 552-1 Commando Barrel Replacement: adım 4, 2 resimden 1. SG 552-1 Commando Barrel Replacement: adım 4, 2 resimden 2.

    • Turn the gun over so that you are facing the bottom of the gun.

    • Using a Phillips #1 screwdriver, remove the following screws:

    • Remove the 8mm screw located directly underneath the cocking lever.

    • Remove the 8mm screw beside the one you just removed.

    Düzenle

  6. SG 552-1 Commando Barrel Replacement: adım 5, 2 resimden 1. SG 552-1 Commando Barrel Replacement: adım 5, 2 resimden 2.

    • Carefully tug on the tip of the gun and pull the barrel and its cover out.

    Düzenle

  7. SG 552-1 Commando Barrel Replacement: adım 6, 3 resimden 1. SG 552-1 Commando Barrel Replacement: adım 6, 3 resimden 2. SG 552-1 Commando Barrel Replacement: adım 6, 3 resimden 3.

    • Pull the barrel out from the cover.

    • Remove the pieces at the end of the barrel.

    Düzenle

  8. SG 552-1 Commando Barrel Replacement: adım 7, 2 resimden 1. SG 552-1 Commando Barrel Replacement: adım 7, 2 resimden 2.

    • Remove the remaining pieces of on the ends of the barrel.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

5 tane daha katılımcı ile

Laura Schulz

Üyelik tarihi: 10/05/12

1 İtibar

1 Kılavuz yazıldı

Rozetler: 1

Ekip

Cal Poly, Team 18-41, Regan Fall 2012 Cal Poly, Team 18-41, Regan Fall 2012 üyesi

CPSU-REGAN-F12S18G41

6 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 8

Son 30 gün: 10

Her zaman: 1,652