Eşyalarını Tamir Et Topluluk Mağaza

SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement

Tıbbi Ekipman
iFixit de, bu onarım kılavuzu da tıbbi cihaz üreticisi tarafından onaylanmış değildir ya da herhangi birinin üreticiyle alâkası yoktur.

Giriş

For more information on replacing the main circuit board, please refer to page 25 in the service manual.

Neye ihtiyacın var

  1. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement, How to Open and Close Housing (SOMNOcomfort and SOMNObalance Ventilator): adım 1, 1 resimden 1.

    • Remove the covering cap. (pg. 23)

    Düzenle

  2. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 2, 1 resimden 1.

    • Place the unit upside down on a non-slip surface and remove the six screws. (pg. 23)

    Düzenle

  3. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 3, 1 resimden 1.

    • Remove the lower part of the housing with a swiveling motion away to the side. Note the SOMNOcomfort series uses a shorter circuit board than the balance series ventilator. (pg. 23)

    Düzenle

  4. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 4, 3 resimden 1. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 4, 3 resimden 2. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 4, 3 resimden 3.

    • Remove the connector (X1) from the circuit board.

    • Pull the connecting cable (64) from its mount.

    • Now set aside the lower part of the housing. (pg. 23)

    Düzenle

  5. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 5, 2 resimden 1. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 5, 2 resimden 2.

    • Next, how to close the compartment and reverse the process.

    • Hold the lower part of the housing to the upper part at an angle

    • Attach the connector (X1) to the main circuit board. When doing so the connector’s nub has to point towards the lock. (pg. 24)

    Düzenle

  6. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 6, 2 resimden 1. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 6, 2 resimden 2.

    • Properly align the main circuit board inside the unit.

    • Attach the connecting cable (64) to its mount (pg. 24)

    Düzenle

  7. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 7, 1 resimden 1.

    • Place the lower part of the housing on the upper part (47). Please make sure the main circuit board (44) is aligned properly, and that the connecting cable (64) is not being squeezed anywhere. (pg. 24)

    Düzenle

  8. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 8, 1 resimden 1.

    • Now reattach the upper part of the housing by tightening the six screws. (pg. 24)

    Düzenle

  9. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 9, 1 resimden 1.

    • Insert the covering cap. (pg. 24)

    Düzenle

  10. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement, Main Circuit Board: adım 10, 1 resimden 1.

    • Pull the plug X200 and X400 from the main circuit board.

    Düzenle

  11. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 11, 1 resimden 1.

    • Remove the flat cables from front panel foil and display: To do so, pull the lock. Once you have pulled the lock, you can remove the flat cable.

    Düzenle

  12. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 12, 1 resimden 1.

    • Remove pressure measurement tube 45 from the pressure sensor or pull out the tube adapter of the pressure measurement tube.

    Düzenle

    • Remove the main circuit board 44.

    Düzenle

  14. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 14, 1 resimden 1.

    • Attach tube 45 to the pressure sensor of a new main circuit board 44 or connect the tube adapter of the pressure measurement tube to the angular bush on the pressure sensor.

    Düzenle

  15. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 15, 1 resimden 1.

    • Reattach the flat wires of front panel foil and display to the main circuit board: – Pull the lock. – Insert the flat cable into the connector. – Push the lock back in.

    Düzenle

  16. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 16, 1 resimden 1.

    • Connect plugs X200 and X400 to the main circuit board.

    Düzenle

  17. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: adım 17, 1 resimden 1.

    • Close the unit

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

2 tane daha katılımcı ile

Brandon Yowakim

Üyelik tarihi: 01/18/18

1.182 İtibar

2 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

Cal Poly, Team S1-G3, Zimmerman Spring 2020 Cal Poly, Team S1-G3, Zimmerman Spring 2020 üyesi

CPSU-ZIMMERMAN-S20S1G3

5 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 1

Her zaman: 185