Parçalar

Hiçbir parçaya gerek yok.

Locate the button on the bottom of the phone. Once located, press and hold the button down.
  • Locate the button on the bottom of the phone. Once located, press and hold the button down.

Yorum Ekle

While holding the button down, remove the back cover of the phone.
  • While holding the button down, remove the back cover of the phone.

Yorum Ekle

  • Use the size 00 Phillips screwdriver to remove the four screws located on the back of the phone. These screws are circled in yellow in the given image.

Yorum Ekle

  • Using the same 00 Phillips screwdriver, remove the two screws at the bottom back plate of the phone near the camera and the speaker.

  • These screws will be 7.25 mm long.

Yorum Ekle

  • Before proceeding, locate the USB port (where the charger can be plugged in) and open it using the iFixit Opening Tool.

  • Failure to open USB port cover at this stage may result in damaging the device.

Yorum Ekle

  • Remove the screws on either side of the camera/speaker with a Phillips 00 screwdriver.

  • These screws will be 5.45 mm long.

Yorum Ekle

  • Use the iFixit Opening Tool to begin removing the camera/speaker from the logic board.

  • Practice caution to prevent damage to the attaching ribbon.

Yorum Ekle

  • To completely remove the camera/speaker, locate the orange attachment beneath it (as shown in the image).

  • Then, use the iFixit Opening Tool to gently pry the camera/speaker off.

Yorum Ekle

  • Use the iFixit Opening Tool to pop off the yellow tab on the logic board.

Yorum Ekle

  • Use the iFixit Opening Tool to pop off the other orange tab to free the logic board.

Yorum Ekle

  • To completely remove the logic board, use the iFixit Opening Tool to pop it up, then use your fingers to pull it out.

  • Do not be alarmed if the volume and hold switch buttons are removed from the logic board.

Yorum Ekle

  • Open/swivel the phone so the back of the LCD panel is visible.

  • Use the iPod opening tool to pry the keypad from the hinge on the back of the device.

  • A moderate amount of force may need to be applied.

Yorum Ekle

  • Using your fingernail, remove the stickers covering the screws on the back of the LCD casing.

  • Using a phillips 00 screwdriver, remove all six screws on the back of the device.

  • These screws will be 3.45 mm long.

Yorum Ekle

  • Using a generous amount of force, use your hands to pry loose the casing from the LCD panel.

  • If necessary, use the iPod opening tool to completely free the casing.

  • Be careful not to sever the wire connecting the outer casing to the display board.

Yorum Ekle

  • Using the iPod opening tool, remove the click wheel from the board.

  • After you have freed the edges, use the spudger to release the clip holding it flush to the board.

Yorum Ekle

  • Unlock the ribbon connection by pressing down on the black clip.

  • Carefully pull the click wheel away from the device.

Yorum Ekle

  • Using tweezers, grip the red and blue wires that attach the audio earpiece to the outer casing and pull.

  • This is glued on so a moderate amount of force may be needed.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 başka kişi bu kılavuzu tamamladı.

Ryan Turner

Üyelik tarihi: 15-04-2010

99 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 6-18, Maness Spring 2010 Cal Poly, Team 6-18, Maness Spring 2010 üyesi

CPSU-MANESS-S10S6G18

3 Üyeler

12 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 2

Her zaman: 2,191