Ana içeriğe geç

Sceptre X9 Komodo VII Power Supply Unit Replacement

Neye ihtiyacın var

  1. Sceptre X9 Komodo VII Power Supply Unit Replacement, Stand: adım 1, 1 resimden 1.
    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

  2. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 2, 1 resimden 1.
    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

  3. Sceptre X9 Komodo VII Power Supply Unit Replacement, Board Cover: adım 3, 1 resimden 1.
    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

  4. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 4, 3 resimden 1. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 4, 3 resimden 2. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 4, 3 resimden 3.
    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

  5. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 5, 2 resimden 1. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 5, 2 resimden 2.
    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

  6. Sceptre X9 Komodo VII Power Supply Unit Replacement, Power Supply Unit: adım 6, 1 resimden 1.
    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

  7. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 7, 3 resimden 1. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 7, 3 resimden 2. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 7, 3 resimden 3.
    • Unplug the seven connections from the power supply unit by gently pulling on them.

  8. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 8, 1 resimden 1.
    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

  9. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 9, 2 resimden 1. Sceptre X9 Komodo VII Power Supply Unit Replacement: adım 9, 2 resimden 2.
    • Lift the power supply unit straight up to remove it from the back panel.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Jose Carrillo

Üyelik tarihi: 09/26/12

23 İtibar

1 Kılavuz yazıldı

Ekip

Cal Poly, Team 16-56, Forte Fall 2012 Cal Poly, Team 16-56, Forte Fall 2012 üyesi

CPSU-FORTE-F12S16G56

5 Üyeler

13 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 5

Her zaman: 664