Eşyalarını Tamir Et Topluluk Mağaza

Shark ION Robot 750 Outer Shell Replacement

Giriş

Suppose the Shark ION R750‘s outer shell is cracked or damaged due to wear and tear, accidental drops, or other potentially damaging impacts. In that case, you must replace the casing to avoid further damage to the vacuum's internal components.

The Shark's outer shell protects the vacuum's internal components from debris, dust, and contaminants that will clog the vacuum, impact the motor, or damage the device's overall performance. Therefore, it is crucial to immediately replace the outer shell so the vacuum continues functioning correctly.

Neye ihtiyacın var

  1. Shark ION Robot 750 Outer Shell Replacement, Outer Shell: adım 1, 3 resimden 1. Shark ION Robot 750 Outer Shell Replacement, Outer Shell: adım 1, 3 resimden 2. Shark ION Robot 750 Outer Shell Replacement, Outer Shell: adım 1, 3 resimden 3.

    • Make sure the device is completely powered off before working.

    • Flip over the vacuum on a flat and uncluttered service with the bottom facing upwards.

    • Remove all seven 9.1mm Torx T15 screws from the device’s front bumper.

    • Remove the nine 9.1mm Torx T6 bolts from outer shell.

    Düzenle

  2. Shark ION Robot 750 Outer Shell Replacement: adım 2, 2 resimden 1. Shark ION Robot 750 Outer Shell Replacement: adım 2, 2 resimden 2.

    • Slightly pull front bumper to expose internal wiring.

    • Unplug the device’s front bumper wiring and completely remove front bumper.

    Düzenle

  4. Shark ION Robot 750 Outer Shell Replacement: adım 3, 2 resimden 1. Shark ION Robot 750 Outer Shell Replacement: adım 3, 2 resimden 2.

    • Remove the four 9.5mm Torx T6 bolts on the yellow brush frame.

    • Gently depress the two tabs on the frame, then lift the frame to remove it.

    Düzenle

  5. Shark ION Robot 750 Outer Shell Replacement: adım 4, 2 resimden 1. Shark ION Robot 750 Outer Shell Replacement: adım 4, 2 resimden 2.

    • Pick up the brush and remove it from the vacuum.

    • Push the brush to your right and lift it.

    Düzenle

  6. Shark ION Robot 750 Outer Shell Replacement: adım 5, 3 resimden 1. Shark ION Robot 750 Outer Shell Replacement: adım 5, 3 resimden 2. Shark ION Robot 750 Outer Shell Replacement: adım 5, 3 resimden 3.

    • Press and hold the dust bin removal button to slide out the dust bin.

    Düzenle

  7. Shark ION Robot 750 Outer Shell Replacement: adım 6, 1 resimden 1.

    • Lift the outer shell to expose the Shark’s interior.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Youness Elfath

Üyelik tarihi: 09/13/23

183 İtibar

1 Kılavuz yazıldı

Rozetler: 3

Ekip

University of North Texas, Team 1-7, Kilpatrick Fall 2023 University of North Texas, Team 1-7, Kilpatrick Fall 2023 üyesi

UNT-KILPATRICK-F23S1G7

4 Üyeler

5 adet Kılavuz yazıldı

0Kılavuz Yorumları

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 7

Her zaman: 134