Giriş

The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum's belt is designed to last approximately 7 years. Replacement of the belt is needed to keep the vacuum at optimal working condition. This replacement guide demonstrates how to replace the belt in the vacuum.

  1. Turn the vacuum on its side.
    • Turn the vacuum on its side.

    • Using a quarter, twist the three green locks to the unlock position.

    • Pull the bottom roller brush cover to open the vacuum.

    Yorum Ekle

  2. Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.
    • Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    Yorum Ekle

    • Remove the three 14.3 mm screws with a T20 screwdriver.

    Yorum Ekle

    • Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    Yorum Ekle

    • Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    Yorum Ekle

    • Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    Yorum Ekle

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    Yorum Ekle

    • Turn the vacuum around.

    • Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    Yorum Ekle

    • Remove both of the headlight covers with the spudger.

    Yorum Ekle

    • Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    Yorum Ekle

    • Remove the two 13.4 mm screws with a T20 bit screwdriver.

    Yorum Ekle

    • Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    Yorum Ekle

    • Remove the visible side of the belt from the gear with a spudger.

    Yorum Ekle

    • Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    Yorum Ekle

    • Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    Yorum Ekle

    • Remove the belt from the gear.

    Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Dakota Rodriguez-Ransom

Üyelik tarihi: 08-10-2018

587 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team S4-G6, White Fall 2018 Cal Poly, Team S4-G6, White Fall 2018 üyesi

CPSU-WHITE-F18S4G6

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 21

Son 30 Gün: 21

Her zaman: 58