Giriş

This is a detialed repair manual to show how to properly remove and install speakers in the Sony Vaio PCG-6J2L.

Hazards

Keep out of reach of children and pets.

DO NOT attempt to teardown or repair your device under the influence of drugs or alcohol.

DO NOT ingest any parts of the system.

Use the correct tools as stated in the tools section.

DO NOT touch any gold connectors on interior or exterior of the system.

Make sure system is unplugged before performing any maintenance on the system.

Parçalar

Hiçbir parçaya gerek yok.

Set the computer display-side down.
  • Set the computer display-side down.

  • Unlock the battery by sliding the port-side latch to the 'unlock' position.

Yorum Ekle

On the opposite side of the battery, press the release latch and slide the battery away from the main body to remove.
  • On the opposite side of the battery, press the release latch and slide the battery away from the main body to remove.

Yorum Ekle

  • Ignore the removal of the heat sink and memory panels as depicted. They do not need to be removed for the completion of this guide.

  • Remove the Torx security screw near the center of the battery-side edge.

Yorum Ekle

  • Press the tabs on each side of the display-side of the keyboard with the flat edge of a spudger.

  • Pull the keyboard toward the mouse pad and gently lift up.

Yorum Ekle

  • The keyboard is still attached by ribbon cable, don't try to remove the keyboard entirely yet.

  • Disconnect the ribbon cable by pressing the tabs on either side of the connector. Pull the cable out parallel to the connector.

  • Remove the keyboard.

Yorum Ekle

  • Turn the laptop upside down.

  • Remove the three screws from the front mouse panel located on the bottom of the laptop.

  • Carefully flip the laptop back over. Remove three more screws from the top securing the panel. A ribbon cable will still be attached to the panel when you remove it.

Yorum Ekle

  • Lift the mouse assembly just enough to access the connecting ribbon cable.

  • Lift the ribbon cable lock to remove the cable.

  • Carefully remove the mouse panel assembly and set aside.

Yorum Ekle

  • Remove the four screws from the underside of the computer. These screws are located underneath where the battery sits and secure the top keyboard panel.

  • To remove the panel below the screen, press up on the two tabs holding the panel in and lift up. The panel should pop off.

  • Before proceeding, remove all black tape holding down wires and other cabling.

Yorum Ekle

  • Pop off the antenna using a pair of tweezers.

Yorum Ekle

  • Remove the seven philips screws holding the speaker assembly in place.

  • Before removing the assembly, disconnect the ribbon cable located at the top left corner of the assembly.

  • The speaker assembly will come off with the display assembly.

Definitely not 7 screws, could be 6 but I am guessing it was 2 like on the picture, the rest was removed before and the 3rd from the right is a push-button :P

I still need to do the reassembly, I will try to pay attention to these details and take some pictures to improve the guide.

oppermafkees - Yanıt

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Ryan

Üyelik tarihi: 11-04-2010

152 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 25-89, Amido Spring 2010 Cal Poly, Team 25-89, Amido Spring 2010 üyesi

CPSU-AMIDO-S10S25G89

4 Üyeler

52 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 Gün: 2

Son 30 Gün: 9

Her zaman: 3,830