Menü

Ayarlarınız

Tezgahım

Cihazlarınız için kılavuz, parça ve cevaplara hızlı erişim edinin
Sepetim

Sepetiniz boş görünüyor

Mağazamıza Göz Atın

The Sharper Image Literati Tablet Keyboard Replacement

Yazan: Spencer Dodder (ve bir diğer katılımcı)
  • Yorumlar: 0
  • Favoriler: 0

Zorluk

Orta

Adımlar

14

Gerekli Süre

30 dakika - 1 saat

Bölümler

3

İşaretler

0

Giriş

The Sharper Image Literati Tablet's Keyboard may need to be replaced due to wear on the keys within a few years of purchase. The Keyboard replacement for The Sharper Image Tablet can be done in approximately half an hour to forty five minutes with moderate difficulty level in nineteen steps. Keyboard replacement for The Sharper Image Literati Tablet can help your device look new once more.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parça belirtilmedi.

  1. Wedge plastic spudger tool between the back panel and the body of device.

    • Wedge plastic spudger tool between the back panel and the body of device.

    • Pry apart the back panel and the device.

    Düzenle

  2. Desolder the battery wires from the circuit board.

    • Desolder the battery wires from the circuit board.

    Düzenle

  3. Warm the battery with a hair dryer.

    • Warm the battery with a hair dryer.

    • Be carful not to over-heat the battery, this could cause the battery to ignite.

    Düzenle

  4. Gently wedge a spudger or thin plastic card between the battery and the body of device. Work the spudger or card along the length of the battery to free it from the adhesive.

    • Gently wedge a spudger or thin plastic card between the battery and the body of device. Work the spudger or card along the length of the battery to free it from the adhesive.

    • Do not bend or puncture the battery. Work slowly and carefully.

    Düzenle

  5. Use a Phillips #00 screwdriver to remove the fifteen 4mm screws from the silver peripheral edging.

    • Use a Phillips #00 screwdriver to remove the fifteen 4mm screws from the silver peripheral edging.

    Düzenle

  6. MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now

    MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now

  7. Use a Phillips #00 screwdriver to remove three 4 mm screws from the circuit board containing the headphone jack and power jack.

    • Use a Phillips #00 screwdriver to remove three 4 mm screws from the circuit board containing the headphone jack and power jack.

    Düzenle

  8. Remove the circuit board.

    • Remove the circuit board.

    Düzenle

  9. Unclip ZIF clip from the chip and unplug ribbon cable.

    • Unclip ZIF clip from the chip and unplug ribbon cable.

    Düzenle

  10. Detach the peripheral edge with plastic wedge.

    • Detach the peripheral edge with plastic wedge.

    • This may require a little hard pulling.

    Düzenle

  11. Remove peripheral silver edge.

    • Remove peripheral silver edge.

    Düzenle

  12. Remove screws from the large metal shielding.

    • Remove screws from the large metal shielding.

    Düzenle

  13. Remove the silver backing plate and the adhered SD port chip.

    • Remove the silver backing plate and the adhered SD port chip.

    Düzenle

  14. Remove the 10 Phillips head 4.2 mm screws using PH#00 screwdriver from the key board chip.

    • Remove the 10 Phillips head 4.2 mm screws using PH#00 screwdriver from the key board chip.

    Düzenle

  15. Peal back the sensor array and keypad. Peal back the sensor array and keypad.

    • Peal back the sensor array and keypad.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

1 tane daha katılımcı ile

Spencer Dodder

Üyelik tarihi: 21-03-2018

533 İtibar

4 adet Kılavuz yazıldı

Rozetler: 4

+1 tane daha rozet

Takım

IUPUI, Team S5-G4, Baechle Spring 2018 IUPUI, Team S5-G4, Baechle Spring 2018 üyesi

IUPUI-BAECHLE-S18S5G4

3 Üyeler

4 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 0

Her zaman: 58