Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

Giriş

Before beginning this guide you should have completed guides on removing the back cover and separating the circuit board from the front cover.

Parçalar

Hiçbir parça belirtilmedi.

  1. Remove the 4 .4mm screws on the back of the device. Remove the 4 .4mm screws on the back of the device.
    • Remove the 4 .4mm screws on the back of the device.

  2. Using the palate knife tool, pry the back from the LCD screen. Apply a moderate pressure to separate them.
    • Using the palate knife tool, pry the back from the LCD screen. Apply a moderate pressure to separate them.

    • You can rotate TOMTOM XL to make prying back off easier.

    • Be careful not to injure the two wires connecting the pieces.

  3. After prying both halves apart, they will be connected by two wires.
    • After prying both halves apart, they will be connected by two wires.

    • Carefully set the two halves next to each other making sure not to stress or damage the wires.

  4. LCD iPhone Ekran Tamir Kit'leri

    Ömür Boyu Garantimiz kapsamındaki bütçe seçeneği.

    Shop Kits

    LCD iPhone Ekran Tamir Kit'leri

    Onarım maliyetlerini düşürün, kaliteyi değil.

    Shop Kits
  5. Using the tweezers separate the wires connecting the battery and speaker to the mother board. Be gentle while pulling the wires out, the plugs are easily injured.
    • Using the tweezers separate the wires connecting the battery and speaker to the mother board.

    • Be gentle while pulling the wires out, the plugs are easily injured.

  6. Locate the 4 .4mm screws connecting the circuit board to the front panel. Use the T6 Torx screwdriver and remove the four screws.
    • Locate the 4 .4mm screws connecting the circuit board to the front panel.

    • Use the T6 Torx screwdriver and remove the four screws.

  7. Locate the ribbon cable connecting the front panel to the circuit board. Locate the white tab locking the ribbon in place. Using precision tweezers push the left and right side of the tab forward.
    • Locate the ribbon cable connecting the front panel to the circuit board.

    • Locate the white tab locking the ribbon in place.

    • Using precision tweezers push the left and right side of the tab forward.

    • Gently pull the ribbon to disconnect the circuit board from the front panel.

    • If gently pulling on the ribbon doesn't release it then the tab hasn't been pushed far enough forward.

  8. Use the palate knife to pry the screen away from the front panel. Pry between the light gray board and the black boarder of the TOMTOM XL screen. Use moderate pressure when prying, slide the palate knife back and forth, and eventually the screen should pop out.
    • Use the palate knife to pry the screen away from the front panel.

    • Pry between the light gray board and the black boarder of the TOMTOM XL screen.

    • Use moderate pressure when prying, slide the palate knife back and forth, and eventually the screen should pop out.

Sonuç

To reassemble your device, follow these instructions in reverse order.

DeVhan

Üyelik tarihi: 11-03-2015

401 İtibar

4 adet Kılavuz yazıldı

Takım

Colorado Springs, Team 9-6, Panko Spring 2015 Colorado Springs, Team 9-6, Panko Spring 2015 üyesi

UCCS-PANKO-S15S9G6

3 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 2

Son 30 gün: 4

Her zaman: 633