1. Unlatch the battery by pushing outward on both latches.
    • Unlatch the battery by pushing outward on both latches.

    Yorum Ekle

  2. Slide battery out.
    • Slide battery out.

    Yorum Ekle

    • Remove the five "F2" screws with a Phillips #0 screwdriver.

    Yorum Ekle

    • Insert the plastic opening tool above the F1 key.

    • Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.

    Yorum Ekle

    • Find the screws above the F1 and INS keys.

    • Unscrew both screws with a Phillips #0 screwdriver.

    Yorum Ekle

    • Slowly lift the top edge of the keyboard out with your fingers.

    • The ribbon cable located on the back of the keyboard will become accessible.

    Yorum Ekle

    • Locate the black ribbon cable flap.

    • Detach flap with plastic opening tool. The ribbon cable will become free.

    Yorum Ekle

    • Your keyboard has now been successfully removed.

    Yorum Ekle

    • Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.

    Yorum Ekle

    • Locate and remove the circled screw with a Phillips #0 screwdriver.

    Yorum Ekle

  3. GIVE TOOLS. FIX FOREVER.

    GIVE TOOLS.

    FIX FOREVER.

    Spread the Fixmas cheer.

    GIVE TOOLS. FIX FOREVER.

    Spread the Fixmas cheer.

    • Use the plastic opening tool to pry the CD/DVD drive out of the frame.

    Yorum Ekle

    • Gently remove the CD/DVD drive from the laptop body.

    Yorum Ekle

    • Remove the circled screws with Phillips #0 screwdriver.

    Yorum Ekle

    • Remove these screws from the underside of the laptop with Phillips #0 screwdriver.

    Yorum Ekle

    • Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.

    • Note: Yours may only have two (2) antennas. Pay attention to the Orientation of the Aluminum bracket with the pads for reinstallation.

    Yorum Ekle

    • Remove the circled screw with a Phillips #0 screwdriver.

    Yorum Ekle

    • Detach the 3 marked cables by pulling them out with you fingers as shown.

    • This may require some force. They do not come out easily.

    Yorum Ekle

    • Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.

    Yorum Ekle

    • Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.

    Yorum Ekle

    • Remove the circled motherboard screws with a Phillips #0 Scewdriver.

    • Disconnect this ribbon cable.

    Yorum Ekle

    • Remove these screws with a Phillips #0 screwdriver.

    Yorum Ekle

    • Detach the display cable by gently pulling it out with your fingers.

    Yorum Ekle

    • Remove the motherboard from the left side by gently lifting the left side upward.

    • The boxed volume control may snag on the laptop frame when pulling the motherboard out.

    Yorum Ekle

    • The motherboard has now been removed from laptop.

    Yorum Ekle

    • Detach the fan power cord by pulling it out with your fingers.

    • Carefully lift up the tape on the fan by peeling the right edge to the left. It can remain attached to the heatsink but should be removed from the fan.

    Yorum Ekle

    • Remove the circled screws with a Phillips #0 screwdriver.

    Yorum Ekle

    • Locate the 3 circled clips holding the fan to the motherboard.

    • Pry each clip outward while applying upward force on the fan as shown.

    Yorum Ekle

    • Carefully pull out the fan.

    • Note: replacing the fan is highly reccomended

    • Optionally you may clean the fan with Air + Q-Tips. To remove the blade turn the fan over and gently pull the fan blade from the housing.

    • If the fan is no longer operational, it may be possible to temporarily repair it by removing the fan blade and put a small amount of WD-40 on the pinion shaft hole the fan rotates in. A toothpick is a good applicator. Do NOT contaminate the motor area with any of the dust/grime that has accumulated.

    • Insert the fan blade and move the blades with your finger. It should spin freely and cog to a stop. Again this is a temporary fix!

    Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Michael Jensen

Üyelik tarihi: 18-04-2011

417 İtibar

6 adet Kılavuz yazıldı

Takım

Cal Poly, Team 4-3, Regan Spring 2011 Cal Poly, Team 4-3, Regan Spring 2011 üyesi

CPSU-REGAN-S11S4G3

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 8

Her zaman: 5,748