Unlatch the battery by pushing outward on both latches.
  • Unlatch the battery by pushing outward on both latches.

Yorum Ekle

Slide battery out.
  • Slide battery out.

Yorum Ekle

Remove the five "F2" screws with a Phillips #0 screwdriver.
  • Remove the five "F2" screws with a Phillips #0 screwdriver.

Yorum Ekle

Insert the plastic opening tool above the F1 key. Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.
  • Insert the plastic opening tool above the F1 key.

  • Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.

Yorum Ekle

Find the screws above the F1 and INS keys. Unscrew both screws with a Phillips #0 screwdriver.
  • Find the screws above the F1 and INS keys.

  • Unscrew both screws with a Phillips #0 screwdriver.

Yorum Ekle

Slowly lift the top edge of the keyboard out with your fingers. The ribbon cable located on the back of the keyboard will become accessible.
  • Slowly lift the top edge of the keyboard out with your fingers.

  • The ribbon cable located on the back of the keyboard will become accessible.

Yorum Ekle

Locate the black ribbon cable flap. Detach flap with plastic opening tool.  The ribbon cable will become free.
  • Locate the black ribbon cable flap.

  • Detach flap with plastic opening tool. The ribbon cable will become free.

Yorum Ekle

Your keyboard has now been successfully removed.
  • Your keyboard has now been successfully removed.

Yorum Ekle

Mac RAM Kitleri
Mac'inizi hızlandırın. Hafızasını maksimuma çıkarın.
Mac RAM Kitleri
Mac'inize daha fazla bellek alın.
Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.
  • Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.

Yorum Ekle

Locate and remove the circled screw with a Phillips #0 screwdriver. Locate and remove the circled screw with a Phillips #0 screwdriver.
  • Locate and remove the circled screw with a Phillips #0 screwdriver.

Yorum Ekle

Use the plastic opening tool to pry the CD/DVD drive out of the frame.
  • Use the plastic opening tool to pry the CD/DVD drive out of the frame.

Yorum Ekle

Gently remove the CD/DVD drive from the laptop body.
  • Gently remove the CD/DVD drive from the laptop body.

Yorum Ekle

Remove the circled screws with Phillips #0 screwdriver. Remove the circled screws with Phillips #0 screwdriver.
  • Remove the circled screws with Phillips #0 screwdriver.

Yorum Ekle

Remove these screws from the underside of the laptop with Phillips #0 screwdriver.
  • Remove these screws from the underside of the laptop with Phillips #0 screwdriver.

Yorum Ekle

Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.
  • Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.

  • Note: Yours may only have two (2) antennas. Pay attention to the Orientation of the Aluminum bracket with the pads for reinstallation.

Yorum Ekle

Remove the circled screw with a Phillips #0 screwdriver.
  • Remove the circled screw with a Phillips #0 screwdriver.

Yorum Ekle

Detach the 3 marked cables by pulling them out with you fingers as shown.
  • Detach the 3 marked cables by pulling them out with you fingers as shown.

  • This may require some force. They do not come out easily.

Yorum Ekle

Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.
  • Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.

Yorum Ekle

Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.
  • Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.

Yorum Ekle

Remove the circled motherboard screws with a Phillips #0 Scewdriver.
  • Remove the circled motherboard screws with a Phillips #0 Scewdriver.

  • Disconnect this ribbon cable.

Yorum Ekle

Remove these screws with a Phillips #0 screwdriver.
  • Remove these screws with a Phillips #0 screwdriver.

Yorum Ekle

Detach the display cable by gently pulling it out with your fingers.
  • Detach the display cable by gently pulling it out with your fingers.

Yorum Ekle

Remove the motherboard from the left side by gently lifting the left side upward. The boxed volume control may snag on the laptop frame when pulling the motherboard out.
  • Remove the motherboard from the left side by gently lifting the left side upward.

  • The boxed volume control may snag on the laptop frame when pulling the motherboard out.

Yorum Ekle

The motherboard has now been removed from laptop.
  • The motherboard has now been removed from laptop.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

3 başka kişi bu kılavuzu tamamladı.

Michael Jensen

Üyelik tarihi: 18-04-2011

417 İtibar

6 adet Kılavuz yazıldı

Takım

Cal Poly, Team 4-3, Regan Spring 2011 Cal Poly, Team 4-3, Regan Spring 2011 üyesi

CPSU-REGAN-S11S4G3

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 Gün: 1

Son 30 Gün: 3

Her zaman: 11,136