Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

Giriş

This guide will allow you to replace your Toshiba Satellite's wireless connection card.

  1. Unplug your laptop from any source of power. Lay your laptop on a soft, clean surface as shown. Using the metal spudger, remove the two rubber grips on the bottom face of the laptop, located closest to the hinge.
    • Unplug your laptop from any source of power.

    • Lay your laptop on a soft, clean surface as shown.

    • Using the metal spudger, remove the two rubber grips on the bottom face of the laptop, located closest to the hinge.

    • The grips may be brittle. Be careful when removing them with the metal spudger so as not to damage them.

  2. Remove the ten 5mm Phillips #0 screws that secure the back plate to the computer. Remove the ten 5mm Phillips #0 screws that secure the back plate to the computer. Remove the ten 5mm Phillips #0 screws that secure the back plate to the computer.
    • Remove the ten 5mm Phillips #0 screws that secure the back plate to the computer.

  3. Starting on the edge that is opposite the hinge, use the plastic opening tools to pry the back plate away from the computer. Loosen the three non-hinge edges. Leave a plastic opening tool in each corner to ensure that one side does not snap closed before you are done opening the others.
    • Starting on the edge that is opposite the hinge, use the plastic opening tools to pry the back plate away from the computer.

    • Loosen the three non-hinge edges.

    • Leave a plastic opening tool in each corner to ensure that one side does not snap closed before you are done opening the others.

    • DO NOT lift the back plate away from the computer; it is still connected to the motherboard.

  4. Nintendo Switch Kit'leri

    Oyuna geri dönmek için hızlı bir düzeltme

    Switch Kit'leri Satın Al

    Nintendo Switch Kit'leri

    Oyuna geri dönmek için hızlı bir düzeltme

    Switch Kit'leri Satın Al
  5. To loosen the back plate, lift it slightly and gently pull it away from the hinge. Flip the back plate open towards the power button, but be sure to not pull on the ribbon cable that connects the back plate to the motherboard. Use a plastic opening tool to detach the side of the ribbon cable connected to the computer by prying up gently on the small black lever at the point of attachment.
    • To loosen the back plate, lift it slightly and gently pull it away from the hinge.

    • Flip the back plate open towards the power button, but be sure to not pull on the ribbon cable that connects the back plate to the motherboard.

    • Use a plastic opening tool to detach the side of the ribbon cable connected to the computer by prying up gently on the small black lever at the point of attachment.

  6. Remove the four 3mm Phillips #0 screws connecting the battery to the computer. Remove the four 3mm Phillips #0 screws connecting the battery to the computer. Remove the four 3mm Phillips #0 screws connecting the battery to the computer.
    • Remove the four 3mm Phillips #0 screws connecting the battery to the computer.

  7. Use a plastic opening tool to lift the side of the battery that is closest to the long edge of the computer. As you are pulling the battery away from the computer, unplug it from the side closest to the short edge of the computer. There may be a lot of resistance when unplugging the battery. If there is, try to wiggle the male side of the plug back and forth as you remove it.
    • Use a plastic opening tool to lift the side of the battery that is closest to the long edge of the computer.

    • As you are pulling the battery away from the computer, unplug it from the side closest to the short edge of the computer.

    • There may be a lot of resistance when unplugging the battery. If there is, try to wiggle the male side of the plug back and forth as you remove it.

  8. Remove the tape partially covering the wireless card. It may be helpful to do this using a plastic opening tool. Remove the tape partially covering the wireless card. It may be helpful to do this using a plastic opening tool.
    • Remove the tape partially covering the wireless card. It may be helpful to do this using a plastic opening tool.

  9. Loosen the 3mm  Phillips #0 screw attaching the wireless card to the computer until there is enough room for the wireless card to be lifted past the height of the screw. One or both of the antenna cables attached to the wireless card during may pop off during this step. This is ok.
    • Loosen the 3mm Phillips #0 screw attaching the wireless card to the computer until there is enough room for the wireless card to be lifted past the height of the screw.

    • One or both of the antenna cables attached to the wireless card during may pop off during this step. This is ok.

  10. Remove the wireless card from the computer by gently pulling it in the direction of the further long edge of the computer, at an upwards angle. If either of the antenna cables are still attached to the card, gently pull them off with your hands to free them. If either of the antenna cables are still attached to the card, gently pull them off with your hands to free them.
    • Remove the wireless card from the computer by gently pulling it in the direction of the further long edge of the computer, at an upwards angle.

    • If either of the antenna cables are still attached to the card, gently pull them off with your hands to free them.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Mudassar Abbas Khan

Üyelik tarihi: 19-10-2017

603 İtibar

5 adet Kılavuz yazıldı

Takım

UMass Dartmouth, Team S66-G5, Rockett Fall 2017 UMass Dartmouth, Team S66-G5, Rockett Fall 2017 üyesi

UMASSD-ROCKETT-F17S66G5

3 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 2

Son 30 gün: 7

Her zaman: 469