Eşyalarını Tamir Et Topluluk Mağaza

UP! Plus 2 Spool Holder Replacement

Giriş

The spool holder is a 3D printed part that holds the filament spool and the feed tube, keeping it stable and secure to the system. Be sure to print a spare spool holder prior to replacement.

Neye ihtiyacın var

  1. UP! Plus 2 Spool Holder Replacement, 3D print replacement spool holder: adım 1, 1 resimden 1.

    • Before your spool holder breaks, 3D print a replacement to have on hand. If you didn't preemptively print a replacement you can still print without a spool holder. Just find some way of holding the spool so that it can rotate as the filament gets pulled off.

    • Download the file for a new spool holder here

    Düzenle

  2. UP! Plus 2 Spool Holder Replacement, Remove plastic filaments: adım 2, 3 resimden 1. UP! Plus 2 Spool Holder Replacement, Remove plastic filaments: adım 2, 3 resimden 2. UP! Plus 2 Spool Holder Replacement, Remove plastic filaments: adım 2, 3 resimden 3.

    • Go to "Maintenance" and tell the printer to withdraw the plastic filament from the extrusion assembly. Finish removing the filament by pulling upwards.

    • Wait for a "beeping" sound before removing filament.

    • Cut off any damaged plastic from the end of the filament.

    • Remove the plastic filament tube from the spool.

    Düzenle

  4. UP! Plus 2 Spool Holder Replacement, Remove spool holder: adım 3, 3 resimden 1. UP! Plus 2 Spool Holder Replacement, Remove spool holder: adım 3, 3 resimden 2. UP! Plus 2 Spool Holder Replacement, Remove spool holder: adım 3, 3 resimden 3.

    • Remove the spool from the spool holder by lifting it up and taking it off.

    • Put the end of the filament through the hole on the side of the spool to keep it from unraveling.

    • Slide the spool holder upwards, and then pull outwards.

    Düzenle

  5. UP! Plus 2 Spool Holder Replacement, Replace spool holder: adım 4, 3 resimden 1. UP! Plus 2 Spool Holder Replacement, Replace spool holder: adım 4, 3 resimden 2. UP! Plus 2 Spool Holder Replacement, Replace spool holder: adım 4, 3 resimden 3.

    • Place the new spool holder by pushing it inwards and sliding it down until it locks.

    • Repeat the steps in reverse chronological order to reassemble the printer.

    • The spool should be inserted in way that end of the filament points towards, not away.

    Düzenle
Bitiş Çizgisi

6 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

valerie boyer

Üyelik tarihi: 10/12/14

508 İtibar

4 adet Kılavuz yazıldı

Rozetler: 8

+5 tane daha rozet

Ekip

Cal Poly, Team 14-31, Maness Fall 2014 Cal Poly, Team 14-31, Maness Fall 2014 üyesi

CPSU-MANESS-F14S14G31

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 6

Her zaman: 1,204