Eşyalarını Tamir Et Topluluk Mağaza

Umbrella Stretcher to Rib Joint Repair

Giriş

A really windy day can break an umbrella. In some cases, a joint will break, disconnecting the stretcher from the rib. You will be using a needle and thread in order to replicate the function of the joint that held the stretcher and the rib together. In addition, this guide will also cover how to sew a small rip on the canopy.

Neye ihtiyacın var

  1. Umbrella Stretcher to Rib Joint Repair, Umbrella Stretcher to Rib Joint Repair: adım 1, 2 resimden 1. Umbrella Stretcher to Rib Joint Repair, Umbrella Stretcher to Rib Joint Repair: adım 1, 2 resimden 2.

    • Take the broken part of the stretcher to rib joint.

    • Realign it with the rib assembly.

    Düzenle

  2. Umbrella Stretcher to Rib Joint Repair: adım 2, 1 resimden 1.

    • Take the needle and carefully pass it through one of the holes as seen in the picture.

    • Then pull it back to the same side you went through.

    Düzenle

  3. Umbrella Stretcher to Rib Joint Repair: adım 3, 1 resimden 1.

    • Take the needle and pass it under the stretcher (not through the middle).

    Düzenle

  5. Umbrella Stretcher to Rib Joint Repair: adım 4, 1 resimden 1.

    • Position the needle so that it faces the second hole from the same side you just went through in step 3.

    • Take the needle and pass it through the second hole.

    • Then position the needle so that it faces the first hole from the same side you just went through.

    Düzenle

  6. Umbrella Stretcher to Rib Joint Repair: adım 5, 2 resimden 1. Umbrella Stretcher to Rib Joint Repair: adım 5, 2 resimden 2.

    • Repeat steps 2-4 until the two pieces are held tightly together.

    • Tie a knot to secure it.

    • Refer to step six if the rib punctured the canopy.

    Düzenle

  7. Umbrella Stretcher to Rib Joint Repair: adım 6, 2 resimden 1. Umbrella Stretcher to Rib Joint Repair: adım 6, 2 resimden 2.

    • It is easier to sew when the canopy is closed

    • Take the hole, hold each end and pull outward into a line.

    • Make sure that it is in line with the umbrella canopy seam.

    • Take the needle and thread and form a hemming stitch (see Step 7).

    Düzenle

  8. Umbrella Stretcher to Rib Joint Repair: adım 7, 3 resimden 1. Umbrella Stretcher to Rib Joint Repair: adım 7, 3 resimden 2. Umbrella Stretcher to Rib Joint Repair: adım 7, 3 resimden 3.

    • Begin with a threaded needle and start the stitch at one end of the hole and pull the needle all the way until just before the thread runs out.

    • Then loop back around and go through again.

    • Repeat until you reach the other end.

    • You can form the stitch multiple times to make it more secure.

    Düzenle
Sonuç

The umbrella is fixed now, you may now use the umbrella freely.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

1 tane daha katılımcı ile

Rodrigo Soliva

Üyelik tarihi: 10/26/17

182 İtibar

1 Kılavuz yazıldı

Rozetler: 5

+2 tane daha rozet

Ekip

DePaul University, Team S1-G8, Dush Fall 2017 DePaul University, Team S1-G8, Dush Fall 2017 üyesi

DPU-DUSH-F17S1G8

2 Üyeler

1 Kılavuz yazıldı

2 Yorum

I have a problem with the auto lock, it's a knight bridge umbrella, when i retract it, it doesn't lock in place, can it be fixed or replace the handle in case it's totally eroded?

kamec 01 - Yanıt

I have 2 umbrellas which have both snapped at the hole. Is there a way this technique or a version of it can be used to repair them?

Jenny - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 6

Son 7 gün: 45

Son 30 gün: 142

Her zaman: 11,434