Eşyalarını Tamir Et Topluluk Mağaza

Unbranded UB-15MS10 Back Camera Replacement

Arşivlenmiş Kılavuz
Bu kılavuz sadece arşivsel amaçlarla muhafaza edilmiştir. Onarımınızı gerçekleştirmek için kılavuzun güncel halini kullanın.

Giriş

This guide explains how to replace the back camera on the Unbranded Tablet.

Neye ihtiyacın var

  1. Unbranded UB-15MS10 Back Camera Replacement, Back Panel: adım 1, 1 resimden 1.

    • Remove the cover over the Micro SD outlet by using a plastic opening tool to pry open and push out the cover panel.

    Düzenle

  2. Unbranded UB-15MS10 Back Camera Replacement: adım 2, 1 resimden 1.

    • Remove the two 4-mm #0 screws from the inside of the Micro SD compartment.

    Düzenle

  3. Unbranded UB-15MS10 Back Camera Replacement: adım 3, 2 resimden 1. Unbranded UB-15MS10 Back Camera Replacement: adım 3, 2 resimden 2.

    • Insert blue guitar picks in the crease between the top and bottom panels starting on the same end as the Micro SD slot.

    • Inserting the picks directly under the Micro SD compartment was the easiest place to get started. It still requires some force.

    Düzenle

  5. Unbranded UB-15MS10 Back Camera Replacement: adım 4, 1 resimden 1.

    • Insert the black spudger between the guitar picks in order to pry open gaps between the blue guitar picks.

    • As the gaps open, slide the guitar picks along the sides to separate the panels.

    Düzenle

  6. Unbranded UB-15MS10 Back Camera Replacement: adım 5, 1 resimden 1.

    • Pry all four sides apart using the blue guitar picks and the black spudger until they can easily be pried apart by hand.

    Düzenle

  7. Unbranded UB-15MS10 Back Camera Replacement, Back Camera: adım 6, 1 resimden 1.

    • Remove the small piece of black tape.

    Düzenle

  8. Unbranded UB-15MS10 Back Camera Replacement: adım 7, 1 resimden 1.

    • Remove the black 4-mm #0 screw.

    Düzenle

  9. Unbranded UB-15MS10 Back Camera Replacement: adım 8, 1 resimden 1.

    • To finish removing the camera, disconnect the camera ribbon from the white ZIF connector on the motherboard.

    • There are two very small prongs on the side which need to be pushed towards the center of the connector to remove it.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

Jordan Turk

Üyelik tarihi: 09/21/15

331 İtibar

2 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

IUPUI, Team 2-1, Baechle Fall 2015 IUPUI, Team 2-1, Baechle Fall 2015 üyesi

IUPUI-BAECHLE-F15S2G1

3 Üyeler

3 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 706