Eşyalarını Tamir Et Topluluk Mağaza

VTech InnoTab 2 Camera Replacement

Giriş

Tired of taking pictures with poor quality on your VTech InnoTab 2. Then follow our quick guide to walk you through replacing a faulty camera on your VTech InnoTab 2.

Neye ihtiyacın var

  1. VTech InnoTab 2 Camera Replacement, Battery: adım 1, 3 resimden 1. VTech InnoTab 2 Camera Replacement, Battery: adım 1, 3 resimden 2. VTech InnoTab 2 Camera Replacement, Battery: adım 1, 3 resimden 3.

    • Apply slight pressure and slide the button above the battery cabinet to the right to open.

    • Remove battery cabinet cover by sliding away from the center of device.

    • This device requires 4AA batteries to function without the AC adaptor.

    Düzenle

  2. VTech InnoTab 2 Camera Replacement, Back Panel: adım 2, 3 resimden 1. VTech InnoTab 2 Camera Replacement, Back Panel: adım 2, 3 resimden 2. VTech InnoTab 2 Camera Replacement, Back Panel: adım 2, 3 resimden 3.

    • Remove all nine plastic caps from the back of the device using the plastic opening tool.

    • These covers are made of hard plastic so they may be difficult to remove.

    Düzenle

  4. VTech InnoTab 2 Camera Replacement: adım 3, 3 resimden 1. VTech InnoTab 2 Camera Replacement: adım 3, 3 resimden 2. VTech InnoTab 2 Camera Replacement: adım 3, 3 resimden 3.

    • Remove the hard rubber tab located by the cartridge slot using the plastic opening tool.

    • Be careful not to apply excessive force.

    • Once the rubber tab is removed unscrew the single 7 mm screw using a J0 screwdriver.

    Düzenle

  5. VTech InnoTab 2 Camera Replacement: adım 4, 2 resimden 1. VTech InnoTab 2 Camera Replacement: adım 4, 2 resimden 2.

    • Remove all ten 7mm screws from the back panel of the device using a JO bit screwdriver.

    • Do not use excessive force while removing the screws to prevent damaging the plastic case.

    Düzenle

  6. VTech InnoTab 2 Camera Replacement: adım 5, 2 resimden 1. VTech InnoTab 2 Camera Replacement: adım 5, 2 resimden 2.

    • Using the plastic opening tool, detach the back plate from the front piece.

    • Do not use excessive force. If the back plate does not gently come on double check that all screws were removed.

    • Once the back panel is removed, you will be able to see the motherboard and other components within the device.

    Düzenle

  7. VTech InnoTab 2 Camera Replacement, Camera: adım 6, 3 resimden 1. VTech InnoTab 2 Camera Replacement, Camera: adım 6, 3 resimden 2. VTech InnoTab 2 Camera Replacement, Camera: adım 6, 3 resimden 3.

    • Using the tip of your finger, carefully pull the clip upwards to release the camera connection from the motherboard.

    • The connection to the camera is located on top side of the devices motherboard.

    • Pulling the camera while the connection to the motherboard is still intact can cause damage to the circuit board.

    • Attach the replacement camera and lower the latch until a click sound can be heard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

1 tane daha katılımcı ile

Roberto Valdes

Üyelik tarihi: 10/18/17

302 İtibar

3 adet Kılavuz yazıldı

Rozetler: 7

+4 tane daha rozet

Ekip

USF Tampa, Team S1-G85, Cagle Fall 2017 USF Tampa, Team S1-G85, Cagle Fall 2017 üyesi

USFT-CAGLE-F17S1G85

2 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 4

Son 30 gün: 4

Her zaman: 316