Ana içeriğe geç

Vtech Kidizoom Smart Watch DX Battery Replacement

Neye ihtiyacın var

  1. Vtech Kidizoom Smart Watch DX Battery Replacement, Master Switch: adım 1, 1 resimden 1.
    • Make sure the master switch is "OFF" before disassembly, to avoid an electric shock.

    • Flip the watch over with the back facing up.

  2. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 2, 1 resimden 1.
    • Remove the four 6.0 mm screws on the back plate with the Phillips #00 screwdriver.

  3. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 3, 1 resimden 1.
    • Gently pull the back plate from the watch casing.

  4. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 4, 2 resimden 1. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 4, 2 resimden 2.
    • Lift the master switch from the circuit board.

  5. Vtech Kidizoom Smart Watch DX Battery Replacement, Circuit Board: adım 5, 2 resimden 1. Vtech Kidizoom Smart Watch DX Battery Replacement, Circuit Board: adım 5, 2 resimden 2.
    • The speaker wires are fragile. They may break if excessive force is used to remove the circuit board.

    • Removal of the circuit board requires soldering.

    • Gently push on the display from the front, near the camera. The circuit board and display will pop out through the back.

  6. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 6, 1 resimden 1.
    • Lift the circuit board carefully from the casing, without breaking or detaching the speaker wires at the bottom of the circuit board.

  7. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 7, 1 resimden 1.
    • Note which wire is connected to which lead before continuing. There are no markers on the circuit board to indicate where each wire belongs.

    • De-solder the black speaker wire from the circuit board.

  8. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 8, 1 resimden 1.
    • De-solder the red speaker wire, as in the previous step.

  9. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 9, 1 resimden 1.
    • Wait for the solder to cool down and solidify, then remove the circuit board from the casing.

  10. Vtech Kidizoom Smart Watch DX Battery Replacement, Battery: adım 10, 2 resimden 1. Vtech Kidizoom Smart Watch DX Battery Replacement, Battery: adım 10, 2 resimden 2.
    • Using the plastic opening tool, gently pry the edges of the battery away from from the circuit board.

    • There is a thin layer of adhesive holding the battery to the circuit board. This will remain sticky after prying.

  11. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 11, 1 resimden 1.
    • De-solder the red battery wire from the circuit board.

  12. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 12, 1 resimden 1.
    • Repeat the de-soldering for the black (ground) wire.

  13. Vtech Kidizoom Smart Watch DX Battery Replacement: adım 13, 1 resimden 1.
    • Pull the battery free, and wait for the solder to cool before handling further.

Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

Navin Ramkishun

Üyelik tarihi: 01/20/16

259 İtibar

1 Kılavuz yazıldı

Ekip

USF Tampa, Team 10-6, Remmell Spring 2016 USF Tampa, Team 10-6, Remmell Spring 2016 üyesi

USFT-REMMELL-S16S10G6

4 Üyeler

12 adet Kılavuz yazıldı

Bir Yorum

Where did you bought the battery?

funkysoulbrother - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 11

Son 30 gün: 61

Her zaman: 8,925