Eşyalarını Tamir Et Topluluk Mağaza

Waring 51BL29 Power Cord Replacement

Giriş

The power cord is what provides power to the motor, once its plugged in. Sometimes these can become stripped and worn down, therefore they may need to be replaced. Following this guide will give you detailed instructions on how to remove the power cord.

Neye ihtiyacın var

  1. Waring 51BL29 Power Cord Replacement, Bottom Panel: adım 1, 2 resimden 1. Waring 51BL29 Power Cord Replacement, Bottom Panel: adım 1, 2 resimden 2.

    • Turn the blender on its side so the bottom panel is facing you.

    • Unscrew the 22mm Phillips #1 screw on the indent of the panel.

    • Unscrew the 3 screws in the rubber holes.

    Düzenle

  2. Waring 51BL29 Power Cord Replacement: adım 2, 1 resimden 1.

    • Remove the bottom panel.

    Düzenle

  3. Waring 51BL29 Power Cord Replacement, Drive Coupling: adım 3, 1 resimden 1.

    • Place the screwdriver in the head of the middle flat-head screw.

    Düzenle

  5. Waring 51BL29 Power Cord Replacement: adım 4, 1 resimden 1.

    • Unscrew this screw while holding the coupling with your other hand and not allowing it to rotate.

    • This screw may be reverse-threaded.

    Düzenle

  6. Waring 51BL29 Power Cord Replacement: adım 5, 1 resimden 1.

    • Once the coupling mechanism has been loosened all the way, gently pull it off the top of the blender.

    Düzenle

  7. Waring 51BL29 Power Cord Replacement, Motor: adım 6, 2 resimden 1. Waring 51BL29 Power Cord Replacement, Motor: adım 6, 2 resimden 2.

    • Unscrew the four nuts in the bottom of the motor cavity.

    • Wiggle the motor until it is free and you can remove it.

    Düzenle

  8. Waring 51BL29 Power Cord Replacement: adım 7, 1 resimden 1.

    • Once motor is pulled out, unscrew the 8 mm screw for the green wire from the base of the blender.

    Düzenle

  9. Waring 51BL29 Power Cord Replacement: adım 8, 3 resimden 1. Waring 51BL29 Power Cord Replacement: adım 8, 3 resimden 2. Waring 51BL29 Power Cord Replacement: adım 8, 3 resimden 3.

    • Unscrew each white wire cap in order to free the motor from the power cord.

    • Once wire caps are removed, separate wires carefully.

    Düzenle

  10. Waring 51BL29 Power Cord Replacement, Power Cord: adım 9, 1 resimden 1.

    • Remove the black power cord.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

3 tane daha katılımcı ile

Quinn Vu

Üyelik tarihi: 04/17/17

113 İtibar

1 Kılavuz yazıldı

Rozetler: 3

Ekip

Cal Poly, Team S15-G4, Banghart Spring 2017 Cal Poly, Team S15-G4, Banghart Spring 2017 üyesi

CPSU-BANGHART-S17S15G4

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 6

Son 30 gün: 21

Her zaman: 1,775