Eşyalarını Tamir Et Topluluk Mağaza

Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement

Giriş

This replacement consists of learning how to disassemble an Xbox One Wireless Controller and replace the Bumpers. This guide will be showing the replacement of the left bumper but the same steps can be applied to replace the right bumper. It is common for these bumpers to get damaged and lose usability quickly, especially if the controller is used frequently for gaming. Many games require the use of these bumpers in order to perform important tasks pertinent to the game. This replacement guide will walk you through a step-by-step process of disassembling the Xbox controller, removing the bumpers, and replacing them.

Neye ihtiyacın var

  1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement, Bumper: adım 1, 1 resimden 1.

    • Remove the battery cover.

    • Remove batteries.

    Düzenle

  2. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 2, 3 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 2, 3 resimden 2. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 2, 3 resimden 3.

    • Grip the controller firmly to remove the side handle cover.

    • Use a flathead screwdriver or a spudger to wedge between the seams of the front to the side handle of the controller.

    • Move the flathead screwdriver all the way around the side plates seam and push the plate forward.

    Düzenle

  3. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 3, 2 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 3, 2 resimden 2.

    • Use a screwdriver and punch a hole directly in the center label. There you will find a hidden screw.

    • Remove the five 10mm screws located on the back of the controller using a T8 screwdriver.

    Düzenle

  5. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 4, 2 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 4, 2 resimden 2.

    • Remove the backplate.

    Düzenle

    Comment je galère de ouf pour remettre la coque arrière. J'arrive plus aligner la prise Jack ?

    nawack de Marseille - Yanıt

  6. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 5, 2 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 5, 2 resimden 2.

    • Remove the faceplate.

    Düzenle

  7. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 6, 3 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 6, 3 resimden 2. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 6, 3 resimden 3.

    • Remove the cover piece surrounding the Xbox button off of its pegs.

    • Firmly hold controller and push cover piece up from the pegs.

    • Press the Xbox button down to assist in the unclipping of the piece.

    Düzenle

  8. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 7, 2 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 7, 2 resimden 2.

    • Remove the broken bumper by unclipping it from its pegs.

    • Hold the controller firmly and push the bumper piece up from its pegs to unclip.

    Düzenle

  9. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 8, 3 resimden 1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 8, 3 resimden 2. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: adım 8, 3 resimden 3.

    • Align the replacement bumper onto the pegs, push gently and click into place.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

19 farklı kişi bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

Cristyne Ramirez

Üyelik tarihi: 01/24/18

571 İtibar

1 Kılavuz yazıldı

Rozetler: 9

+6 tane daha rozet

Ekip

USF Sarasota-Manatee, Team S1-G1, Stewart Spring 2018 USF Sarasota-Manatee, Team S1-G1, Stewart Spring 2018 üyesi

USFSM-STEWART-S18S1G1

15 Üyeler

25 adet Kılavuz yazıldı

2 Yorum

On my controller the screws were T8 security type, so you'll need bits with a hole in the middle

Sean H - Yanıt

Is there a way to do this without removing all of the front and grip.

Alan Marantos - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 24

Son 7 gün: 148

Son 30 gün: 665

Her zaman: 47,206