Eşyalarını Tamir Et Onarma Hakkı Mağaza

Xelio P1001A-BK Wi-Fi Antenna Replacement

Yazan: Josh Saenz (ve 4 başka katılımcı)
  • Yorumlar: 0
  • Favoriler: 0

Zorluk

Orta

Adımlar

7

Gerekli Süre

30 dakika

Bölümler

2

İşaretler

1

Action Shots

İşlem Görüntüleri

Öykünün yıldızı olun! Belirli eylemlerin nasıl gerçekleştirileceğini daha iyi göstermek için bu kılavuza resimler gerekli.

Giriş

INFORMATION ABOUT THE COAXIAL WIRE:

  • The wire that connects the Wi-Fi antenna to the motherboard is a coaxial wire.
  • The coaxial wire consists of a wire insulator (plastic), wire braid shield (middle layer), and center conductor (inner layer) surrounded by an insulator.

The connecting points of the coaxial wire to the motherboard are very small and may require a magnifying glass to see clearly.

  1. With a Phillips #0 screwdriver, remove the two 3 mm retaining screws from the side of the tablet. With a Phillips #0 screwdriver, remove the two 3 mm retaining screws from the side of the tablet.

    • With a Phillips #0 screwdriver, remove the two 3 mm retaining screws from the side of the tablet.

    Düzenle

  2. Using the plastic opening tool, disengage the securing tabs that are along the two long sides of the tablet, four on each side.

    • Using the plastic opening tool, disengage the securing tabs that are along the two long sides of the tablet, four on each side.

    • Slowly rotate up the side of the tablet opposite from the control buttons.

    Düzenle

  3. Before fully separating the shell halves, observe if the speakers are separated from the shell half.

    • Before fully separating the shell halves, observe if the speakers are separated from the shell half.

    • If they are, the shell half can be fully separated from the front shell half.

    • If they are still in their sockets, gently pry them loose with the plastic opening tool.

    Düzenle

  5. Desolder the connection on the motherboard. Use a soldering vacuum to remove any excess solder.

    • Desolder the connection on the motherboard.

    • Use a soldering vacuum to remove any excess solder.

    Düzenle

  6. Use wire strippers to strip off at least 2 mm of wire insulation from each wire.

    • Use wire strippers to strip off at least 2 mm of wire insulation from each wire.

    Düzenle

  7. Solder the outer wire braid shield to the ground point.

    • Solder the outer wire braid shield to the ground point.

    Düzenle

  8. Solder the center conductor to the antenna point.

    • Solder the center conductor to the antenna point.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Josh Saenz

Üyelik tarihi: 11-03-2015

316 İtibar

3 adet Kılavuz yazıldı

Rozetler: 7

+4 tane daha rozet

Takım

Colorado Springs, Team 4-2, Panko Spring 2015 Colorado Springs, Team 4-2, Panko Spring 2015 üyesi

UCCS-PANKO-S15S4G2

3 Üyeler

12 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 3

Her zaman: 122