Eşyalarını Tamir Et Topluluk Mağaza

Zeki TBQG884B Digitizer Touch Screen

Giriş

This guide requires three prerequisite guides for the proper replacement of the digitizer screen on the front of the Zeki tablet. Please, take a moment to familiarize yourself with those guides. They can be found in the details section of this guide.

Neye ihtiyacın var

  1. Zeki TBQG884B Digitizer Touch Screen, Rear Case: adım 1, 2 resimden 1. Zeki TBQG884B Digitizer Touch Screen, Rear Case: adım 1, 2 resimden 2.

    • Remove the two screws from the end of the device where the ports are located using a Phillips #1 screwdriver.

    Düzenle

  2. Zeki TBQG884B Digitizer Touch Screen: adım 2, 1 resimden 1.

    • Place the tablet down so that the screen is facing away from you.

    • Insert the tip of your opening tool into the small gap between the gray and white plastic covering. Pry it open and you should hear the clips opening up.

    • Gently work your way around the perimeter of the tablet's edge.

    Düzenle

  3. Zeki TBQG884B Digitizer Touch Screen: adım 3, 2 resimden 1. Zeki TBQG884B Digitizer Touch Screen: adım 3, 2 resimden 2.

    • Remove the back cover

    • Remove any tape on the speaker and detach the speaker from the back plate.

    • The speaker is connected to the motherboard by two soldered wires. Don't break them when you remove the speaker.

    Düzenle

  4. Zeki TBQG884B Digitizer Touch Screen, Motherboard: adım 4, 1 resimden 1.

    • Disconnect the Wi-Fi antenna cable from the motherboard.

    Düzenle

  6. Zeki TBQG884B Digitizer Touch Screen: adım 5, 1 resimden 1.

    • Using the Phillips #1 screwdriver, remove the three screws from the motherboard..

    Düzenle

  7. Zeki TBQG884B Digitizer Touch Screen: adım 6, 1 resimden 1.

    • Open the ZIF connector. Then, remove the ribbon that connects the motherboard and the screen.

    Düzenle

  8. Zeki TBQG884B Digitizer Touch Screen: adım 7, 1 resimden 1.

    • Disconnect the other ZIF connector on the opposite side of the motherboard.

    Düzenle

  9. Zeki TBQG884B Digitizer Touch Screen: adım 8, 1 resimden 1.

    • Remove the motherboard and now reinsert all connectors into a new motherboard.

    • In order to disconnect the battery and speaker wires from the motherboard, soldering is required. Be cautious as the soldering iron is hot.

    Düzenle

  10. Zeki TBQG884B Digitizer Touch Screen, LCD Screen: adım 9, 1 resimden 1.

    • Use an opening tool to detach the clip between the front frame, and the metal loader.

    • There are several clips on each side of the frame. Detach ALL of them before you open the loader.

    Düzenle

  11. Zeki TBQG884B Digitizer Touch Screen: adım 10, 1 resimden 1.

    • Lift the metal loader up and separate it from the LCD screen.

    • Detach each piece slowly to avoid damaging or dropping any fragile parts.

    Düzenle

  12. Zeki TBQG884B Digitizer Touch Screen, Digitizer Touch Screen: adım 11, 1 resimden 1.

    • Separate the display from the digitizer.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Yazar

9 tane daha katılımcı ile

David Wyman

Üyelik tarihi: 09/16/15

343 İtibar

3 adet Kılavuz yazıldı

Rozetler: 13

+10 tane daha rozet

Ekip

IUPUI, Team 1-3, Harley Fall 2015 IUPUI, Team 1-3, Harley Fall 2015 üyesi

IUPUI-HARLEY-F15S1G3

5 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 800