Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

iMac G5 17" Model A1144 Front Bezel Replacement

Yazan: Walter Galan (ve 3 başka katılımcı)
  • Yorumlar: 3
  • Favoriler: 0

Zorluk

Orta

Adımlar

9

Gerekli Süre

Bir süre öner??

Bölümler

2

İşaretler

1

Prerequisite Only

Salt Önkoşul

Bu kılavuzun yalnızca diğer kılavuzlar için bir önkoşul kılavuzu olduğunu lütfen dikkate alın.

Giriş

Remove your front bezel to gain access to your iMac's internals.

  1. Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Loosen the two Phillips screws securing the access door to your iMac.

    • These screws are captive in the access door.

    Düzenle

  2. Remove the access door from your iMac.

    • Remove the access door from your iMac.

    Düzenle

  3. Remove the three T8 Torx screws securing the front bezel to the rear panel.

    • Remove the three T8 Torx screws securing the front bezel to the rear panel.

    Düzenle

  4. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

  5. Orient the iMac face-up, on its backside. Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    • Orient the iMac face-up, on its backside.

    • Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    Düzenle

  6. While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    • While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    Düzenle

  7. Re-orient your iMac so it sits upright on the stand. Insert a plastic card up into the corner of the air vent slot at the top of the rear case. Push the card toward the top of the iMac to release the front bezel latch.

    • Re-orient your iMac so it sits upright on the stand.

    • Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

    • Push the card toward the top of the iMac to release the front bezel latch.

    • Pull the front bezel away from the rear case.

    • Repeat this process for the other side of the front bezel.

    • It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.

    • If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

    Düzenle

  8. Lay your iMac stand-side down on a table.

    • Lay your iMac stand-side down on a table.

    • Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.

    • Lay the front bezel above the rest of the iMac.

    Düzenle

  9. If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    • If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    Düzenle

  10. Disconnect both the camera and microphone cables. Disconnect both the camera and microphone cables.

    • Disconnect both the camera and microphone cables.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 1,145