Eşyalarını Tamir Et Topluluk Mağaza

iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Giriş

Use this guide to install a hard drive in your iMac Intel 20" EMC 2133 or 2210.

  1. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement, Hard Drive: adım 1, 1 resimden 1.

    • If necessary, remove the pieces of tape securing the hard drive/optical drive thermal sensor cables to your iMac.

    Düzenle

  2. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 2, 1 resimden 1.

    • Disconnect the hard drive thermal sensor by pulling its connector toward the top of your iMac.

    • When removing this connector, it is helpful use your thumbnails to push the ears on either side of the connector toward the top of your iMac.

    Düzenle

  3. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 3, 2 resimden 1. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 3, 2 resimden 2.

    • Pressing the top of the hard drive bracket down to release it from the rear case requires a substantial amount of force. We recommend laying your iMac stand-side down on a table to avoid knocking it over.

    • Press the hard drive bracket down toward the bottom edge of your iMac to free it from the rear case, then rotate the top of the drive toward yourself.

    Düzenle

  5. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 4, 2 resimden 1. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 4, 2 resimden 2.

    • Rotate the hard drive toward yourself, then lift it up off its mounting pins.

    • The hard drive is still connected via the SATA cables.

    • When reinstalling your hard drive, be careful not to push the rubber grommets through the openings in the chassis with the lower hard drive pins as retrieving them may require logic board removal.

    Düzenle

  6. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 5, 1 resimden 1.

    • Insert the flat end of a spudger between the SATA power cable connector and the edge of the hard drive.

    • Twist the spudger to separate the connector from the hard drive.

    Düzenle

  7. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 6, 1 resimden 1.

    • Pull the SATA power connector away from the hard drive.

    Düzenle

  8. iMac Intel 20" EMC 2133 and 2210 Hard Drive Replacement: adım 7, 1 resimden 1.

    • Disconnect the SATA data cable by pulling its connector away from the hard drive.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

Bir Yorum

Walter, I was working on a mid-2007 IMac (2133) and found your instructions helpful but not always complete or right. I have added some comments in some of the steps to clarify.

Pablo Guerrero - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 2,877