Bu sürüm, hatalı düzenlemeler içerebilir. En son doğrulanmış bellek kopyası dönün.
Neye ihtiyacın var
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Fill a pot or pan with enough water to fully submerge an iOpener.
-
Heat the water to a boil. Turn off the heat.
-
Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water.
-
Use tongs to extract the heated iOpener from the hot water.
-
Thoroughly dry the iOpener with a towel.
-
Your iOpener is ready for use! If you need to reheat the iOpener, heat the water to a boil, turn off the heat, and place the iOpener in the water for 2-3 minutes.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
Bu adımda kullanılan alet:Safety Glasses$3.19-
Lay the iOpener flat on the right edge of the iPad, smoothing it out so that there is good contact between the surface of the iPad and the iOpener.
-
Let the bag sit on the iPad for approximately 90 seconds before attempting to open the front panel.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
There is a small gap in the iPad's adhesive ring in the upper right corner of the iPad, approximately 2.0 inches (~5 cm) from the top of the iPad. You are going to exploit this weakness.
-
Align the tool with the mute button. Insert the tip of a plastic opening tool into the gap between the front glass and the plastic bezel. Just insert the very tip of the opening tool, just enough to widen the crack.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Make sure you place the tool in the proper spot—between the plastic display bezel and the front panel glass.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Keeping the tip of the plastic opening tool wedged between the front glass and plastic bezel, slide a plastic opening pick in the gap, right next to the plastic opening tool.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the plastic opening tool from the iPad, and push the opening pick further underneath the front glass to a depth of ~0.5 inches.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
While you work on releasing the adhesive on the right side of the iPad, reheat the iOpener, and replace it on the bottom edge of the iPad.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
While the bottom edge is being heated by the iOpener, begin releasing the adhesive from the right edge of the iPad.
-
Slide the opening pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Before removing the first opening pick from the bottom corner of the iPad, insert a second pick under the right edge of the front glass to keep the adhesive from re-adhering.
-
Re-heat the iOpener, and move it to the top edge of the iPad.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
You will have to release the adhesive securing the antenna to the front panel without damaging the delicate parts attaching the antenna to the bottom of the iPad. Follow the next steps carefully.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the opening pick around the bottom right corner of the iPad, releasing the adhesive there.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the tip of the opening pick along the bottom edge of the iPad, releasing the adhesive over the Wi-Fi antenna.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Once you have moved past the Wi-FI antenna (approximately 3" (75 mm) from the right edge, or right next to the home button) re-insert the opening pick to its full depth.
-
Slide the pick to the right, releasing the adhesive securing the Wi-Fi antenna to the front glass.
-
The antenna is attached to the bottom of the iPad via screws and a cable. This step detaches the antenna from the front panel, ensuring that when you remove the panel, the antenna will not be damaged.
-
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Continue releasing the adhesive along the bottom of the iPad, pulling the opening pick out far enough to go around the home button, and re-inserting it to a depth of 1/2 inch (10 mm) once the pick is past the home button.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Continue releasing the adhesive all the way along the bottom edge of the iPad.
-
Leave the opening pick wedged underneath the front glass near the home button.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Reheat the iOpener in the microwave and set it on the left edge of the iPad to start warming the adhesive in that section.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the opening pick along the top edge of the iPad, pulling it out slightly to go around the front-facing camera bracket.
-
The adhesive along this section is very thick, and a fair amount of force may be required. Work carefully and slowly, making sure to not slip and damage yourself or your iPad.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Continue releasing the adhesive along the top edge of the iPad, and slide the opening pick around the top left corner.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the opening pick along the left edge of the iPad, releasing the adhesive as you go. The adhesive is thin here due to the digitizer along the whole left side. Make sure the pick is not too deep (max 1/2 inch) 10 mm to prevent damaging the digitizer.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Using the opening pick that is still underneath the bottom edge of the iPad, release the adhesive along the bottom left corner.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Using one of the opening picks, pry up the bottom right corner of the iPad and grab it with your fingers.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
Bu adımda kullanılan alet:Microfiber Cleaning Cloths$3.99-
Holding the iPad by the top and bottom right corners, rotate the front glass away from the iPad.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the four 2.0 mm Phillips screws securing the LCD to the rear case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Lift the LCD from its long edge closest to the volume buttons and gently flip it out of the rear case—like turning the page in a book.
-
Set the LCD face down on the front panel.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
If present, remove the piece of tape covering the end of the front facing camera cable with a pair of tweezers.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the flat end of a spudger to carefully pry the connector up from its socket on the control board.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the flat end of a spudger to separate the adhesive securing the front facing camera cable to the control board.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Pry the front-facing camera up off the foam adhesive securing it to the rear case.
-
Remove the front-facing camera.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use a pair of tweezers to remove the rubber cover up off the rear-facing camera housing.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the single 3.3 mm Phillips screw from the rear-facing camera metal retainer clip.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Lift the rear-facing camera metal retainer clip straight up from its recess in the rear case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use a plastic opening tool to pry the rear-facing camera connector up from its socket on the control board.
-
Remove the rear-facing camera.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the single 2.1 mm Phillips screw from the rear-facing camera housing.
-
Remove the camera housing from the rear case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the flat end of a spudger to flip up the retaining flap on the button assembly ribbon cable ZIF socket.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Run the tip of a spudger underneath the button assembly cable to free it from the socket.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the flat end of a spudger to flip up the retaining flap on the microphone ribbon cable ZIF socket.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Pull the microphone ribbon cable straight out with a pair of tweezers.
-
Gently bend the cable to keep it out of the way.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the two 2.9 mm Phillips screws securing the headphone jack to the rear case.
-
Pull the headphone jack from its port in the rear case and fold out of the way.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the two 2.1 mm Phillips screws securing the metal bracket to the rear case.
-
Remove the metal bracket from the rear case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
If present, use tweezers to remove the piece of tape covering the end of the headphone jack/control board cable.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the flat end of a spudger to flip up the retaining flap on the headphone jack/control board cable ZIF socket.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the tip of a spudger underneath the ribbon cable to disconnect it.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Gently peel the headphone jack/control board ribbon cable away from the rear case to free it from the adhesive.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the flat end of a spudger to loosen the adhesive under the narrower part of the ribbon cable near the headphone jack.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the flat end of a spudger under the middle portion of the ribbon cable to separate the adhesive holding it to the rear case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Slide the flat end of a spudger under the widest part of the cable to free it from the rear case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
To begin freeing it from adhesive, pry gently under the control board near the front-facing camera socket.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Pry gently under the control board near the rear-facing camera.
-
Carefully pry under the widest part of the board to free the assembly from the last of the adhesive.
-
İptal et: Bu kılavuzu tamamlamadım.
15 farklı kişi bu kılavuzu tamamladı.