Ana içeriğe geç

iPad 3 4G Power & Volume Button Assembly Replacement

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Neye ihtiyacın var

  1. iPad 3 4G Power & Volume Button Assembly Replacement, Power & Volume Button Assembly: adım 1, 1 resimden 1.
    • Remove the following screws securing the power & volume button cable to the aluminum frame:

    • Two 5.5 mm Phillips #0

    • One 2.6 mm Phillips #0

    • Two 2.6 mm Phillips #0

    • The two screws located on top are angled into the aluminum frame. Be sure to always hold the screwdriver in line with the screw.

  2. iPad 3 4G Power & Volume Button Assembly Replacement: adım 2, 1 resimden 1.
    • Remove the piece of plastic covering the volume buttons.

  3. iPad 3 4G Power & Volume Button Assembly Replacement: adım 3, 1 resimden 1.
    • Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.

    • This screw is angled into the aluminum frame. Be sure to always hold the screwdriver in line with the screw.

  4. iPad 3 4G Power & Volume Button Assembly Replacement: adım 4, 2 resimden 1. iPad 3 4G Power & Volume Button Assembly Replacement: adım 4, 2 resimden 2.
    • Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.

    • Move the plastic opening tool around the sensor, releasing the adhesive.

  5. iPad 3 4G Power & Volume Button Assembly Replacement: adım 5, 2 resimden 1. iPad 3 4G Power & Volume Button Assembly Replacement: adım 5, 2 resimden 2.
    • Slide a spudger underneath the power & volume cables, releasing the adhesive.

  6. iPad 3 4G Power & Volume Button Assembly Replacement: adım 6, 2 resimden 1. iPad 3 4G Power & Volume Button Assembly Replacement: adım 6, 2 resimden 2.
    • Using the tip of the spudger rather that the wide edge, release the adhesive underneath the volume button branch of the ribbon cable.

  7. iPad 3 4G Power & Volume Button Assembly Replacement: adım 7, 3 resimden 1. iPad 3 4G Power & Volume Button Assembly Replacement: adım 7, 3 resimden 2. iPad 3 4G Power & Volume Button Assembly Replacement: adım 7, 3 resimden 3.
    • Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.

  8. iPad 3 4G Power & Volume Button Assembly Replacement: adım 8, 2 resimden 1. iPad 3 4G Power & Volume Button Assembly Replacement: adım 8, 2 resimden 2.
    • With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.

  9. iPad 3 4G Power & Volume Button Assembly Replacement: adım 9, 2 resimden 1. iPad 3 4G Power & Volume Button Assembly Replacement: adım 9, 2 resimden 2.
    • Holding the power & volume button cable with with both hands, carefully pull the volume buttons and lock switch from their sockets in the aluminum frame.

    • Lift and remove the power & volume button cable out of the rear aluminum case.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Brett Hartt

Üyelik tarihi: 04/12/10

127.665 İtibar

143 adet Kılavuz yazıldı

Ekip

iFixit iFixit üyesi

Staff

135 Üyeler

16.476 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 129