Ana içeriğe geç

Bu sürüm, hatalı düzenlemeler içerebilir. En son doğrulanmış bellek kopyası dönün.

Neye ihtiyacın var

  1. , iOpener'ı Isıtma: adım 1, 2 resimden 1. , iOpener'ı Isıtma: adım 1, 2 resimden 2.
    • İşleme başlamadan önce mikrodalganızı temizlenmenizi tavsiye ederiz. Aksi takdirde, yüzeydeki yağlı maddeler iOpener'a yapışabilir.

    • iOpener'ı mikrodalga fırının ortasına yerleştirin.

    • Döner tablalı mikrodalga fırınlar için: Tablanın sorunsuz bir şekilde döndüğünden emin olun. Aksi takdirde, iOpener'ınız takılıp fazla ısınabilir ve yanabilir.

  2. : adım 2, 1 resimden 1.
    • iOpener'ı otuz saniye boyunca ısıtın.

    • Tamir süresince iOpener ısınacağı için, tek seferde otuz saniye olmak üzere yeniden ısıtın.

    • Tamir süresince iOpener'ı fazla ısıtmamaya dikkat edin; fazla ısıtma iOpener'ın patlamasına sebep olabilir.

    • iOpener'ın kabarık bir görüntüsü varsa, kesinlikle dokunmayın.

    • iOpener'ın orta kısmı hala dokunulamayacak kadar sıcaksa, tekrar ısıtmadan önce biraz daha kullanabilirsiniz. Doğru bir şekilde ısıtılmış iOpener, yaklaşık 10 dakika kadar sıcak kalacaktır.

  3. : adım 3, 1 resimden 1.
    • iOpener'ı sıcak olan ortasından değil, herhangi iki ucun birinden tutarak mikrodalga fırından çıkartın.

    • iOpener fırından çıktığında epey sıcak olacaktır, dikkat edin. Gerekli ise, fırın eldiveni kullanabilirsiniz.

  4. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 4, 2 resimden 1. : adım 4, 2 resimden 2.
    • If you don't have a microwave, follow this step to heat your iOpener in boiling water.

    • Fill a pot or pan with enough water to fully submerge an iOpener.

    • Heat the water to a boil. Turn off the heat.

    • Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water.

    • Use tongs to extract the heated iOpener from the hot water.

    • Thoroughly dry the iOpener with a towel.

    • The iOpener will be very hot, so be careful to hold it only by the end tabs.

    • Your iOpener is ready for use! If you need to reheat the iOpener, heat the water to a boil, turn off the heat, and place the iOpener in the water for 2-3 minutes.

  5. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 5, 3 resimden 1. : adım 5, 3 resimden 2. : adım 5, 3 resimden 3.
    • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.

    • Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.

    • This will keep glass shards contained and provide structural integrity when prying and lifting the display.

    • Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.

    • Wear safety glasses to protect your eyes, and be careful not to damage the LCD screen.

  6. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 6, 1 resimden 1.
    • Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.

    • Let the iOpener sit for about five minutes to soften the adhesive beneath the glass.

  7. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 7, 3 resimden 1. : adım 7, 3 resimden 2. : adım 7, 3 resimden 3.
    • Carefully place a suction cup halfway up the heated side.

    • Be sure the cup is completely flat on the screen to get a tight seal.

    • While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.

    • Be careful to only lift the glass enough to insert an opening pick—any more and you risk cracking the glass.

  8. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 8, 3 resimden 1. : adım 8, 3 resimden 2. : adım 8, 3 resimden 3.
    • While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad.

    • Don't insert the opening pick any deeper than the black bezel on the side of the display. Inserting the pick too far may damage the LCD.

    • Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.

  9. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 9, 1 resimden 1.
    • Reheat and reapply the iOpener.

    • Be careful not to overheat the iOpener during the repair procedure. Always wait at least ten minutes before reheating the iOpener.

    • Let it rest for a few minutes to reheat the left edge of the iPad.

  10. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 10, 3 resimden 1. : adım 10, 3 resimden 2. : adım 10, 3 resimden 3.
    • Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.

    • Throughout the rest of the procedure, if you encounter significant resistance to sliding picks beneath the glass, stop and reheat the section you're working on. Forcing the picks risks cracking the glass.

  11. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 11, 3 resimden 1. : adım 11, 3 resimden 2. : adım 11, 3 resimden 3.
    • Continue moving the opening pick down the side of the display to release the adhesive.

    • If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.

  12. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 12, 3 resimden 1. : adım 12, 3 resimden 2. : adım 12, 3 resimden 3.
    • Take the first pick you inserted and slide it up toward the top corner of the iPad.

    • If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.

  13. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 13, 1 resimden 1.
    • Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.

    • Be careful not to overheat the iOpener during the repair procedure. Wait at least ten minutes before reheating the iOpener.

    • If you have a flexible iOpener, you can bend it to heat both the upper left corner and the upper edge at the same time.

  14. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 14, 3 resimden 1. : adım 14, 3 resimden 2. : adım 14, 3 resimden 3.
    • Slide the opening pick around the top left corner of the iPad to separate the adhesive.

  15. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 15, 3 resimden 1. : adım 15, 3 resimden 2. : adım 15, 3 resimden 3.
    • Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.

    • The third image shows where the front-facing camera and housing are in the iPad.

    • Avoid sliding the opening pick over the front-facing camera, as you may smear adhesive onto the lens or damage the camera. The following steps will detail how to best avoid disturbing the front-facing camera.

  16. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 16, 3 resimden 1. : adım 16, 3 resimden 2. : adım 16, 3 resimden 3.
    • Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.

  17. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 17, 3 resimden 1. : adım 17, 3 resimden 2. : adım 17, 3 resimden 3.
    • Leave the opening pick in the iPad slightly past the front-facing camera.

    • Take a second pick and insert it to the left of the camera, where the first pick just was. Slide it back to the corner to completely cut any remaining adhesive.

    • Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.

  18. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 18, 3 resimden 1. : adım 18, 3 resimden 2. : adım 18, 3 resimden 3.
    • Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.

  19. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 19, 1 resimden 1.
    • Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.

    • Reheat the iOpener and place it on the remaining long side of the iPad—along the volume and lock buttons.

  20. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 20, 2 resimden 1. : adım 20, 2 resimden 2.
    • Slide the top right opening pick around the corner to fully release the top edge of the glass.

    • Leave this pick in place to keep the adhesive from re-sealing itself, and grab a new pick for the next step.

  21. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 21, 3 resimden 1. : adım 21, 3 resimden 2. : adım 21, 3 resimden 3.
    • Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.

  22. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 22, 3 resimden 1. : adım 22, 3 resimden 2. : adım 22, 3 resimden 3.
    • Continue to slide the pick down the right edge of the iPad, releasing the adhesive.

  23. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 23, 1 resimden 1.
    • Leave the opening picks in place and reheat the iOpener.

    • Remember not to overheat the iOpener—no more than once every ten minutes.

    • Set the reheated iOpener on the home button end of the iPad and let it rest for a few minutes to soften the adhesive beneath the glass.

  24. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 24, 3 resimden 1. : adım 24, 3 resimden 2. : adım 24, 3 resimden 3.
    • Slide the lower left pick to the lower left corner to cut the adhesive on that corner.

    • Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.

    • There are quite a few things to avoid beneath the lower bezel, so study the third image closely:

    • Antennas

    • Home button cavity

    • Digitizer cable

    • The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.

  25. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 25, 3 resimden 1. : adım 25, 3 resimden 2. : adım 25, 3 resimden 3.
    • Leave the pick from the last step in place to prevent the adhesive from re-sealing.

    • With a new pick, slice gently over the left-hand antenna, stopping before the home button.

    • Only slide the pick from the outer edge toward the center of the iPad. Do not move the pick back toward the outer edge, as moving in this direction may damage the antenna.

    • If you need to slide the pick over the lower section more than once, remove it and re-insert at the outer edge, and slide inwards.

    • Leave the pick in place before moving on.

  26. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 26, 3 resimden 1. : adım 26, 3 resimden 2. : adım 26, 3 resimden 3.
    • Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button.

    • Stop about an inch from the right-hand side to avoid cutting the digitizer cable.

    • Insert the pick slightly deeper and work it back toward the home button.

    • Again, be sure to only slide the pick toward the center of the iPad when it is fully inserted; otherwise you may damage the antenna beneath the glass.

  27. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 27, 1 resimden 1.
    • Reheat and reapply the iOpener to the top bezel of the iPad.

  28. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 28, 2 resimden 1. : adım 28, 2 resimden 2.
    • Be very careful with this step. Take your time and ensure the adhesive is hot and soft, and that you've been through all of the adhesive with an opening pick. Don't be afraid to stop and reheat.

    • At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.

    • If you encounter a significant amount of resistance, stop twisting. Leave the picks in place, reheat, and reapply the iOpener to the problem areas, and run a pick through the sticking point one more time.

  29. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 29, 2 resimden 1. : adım 29, 2 resimden 2.
    • Lift slowly and gently to further detach the adhesive along the lower edge.

  30. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 30, 2 resimden 1. : adım 30, 2 resimden 2.
    • Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace.

    • If reusing the front panel assembly during reassembly, you will need to replace your display adhesive. Use our display adhesive application guide to reapply your display adhesive and reseal your device.

  31. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 31, 3 resimden 1. : adım 31, 3 resimden 2. : adım 31, 3 resimden 3.
    • The front-facing camera housing may stick to the front panel; peel up the housing and place it back over the camera to protect it.

    • Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel.

    • Return the front-facing camera housing to its recess in the rear case.

  32. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 32, 2 resimden 1. : adım 32, 2 resimden 2.
    • Remove the following Phillips #00 screws securing the LCD:

    • Three 3.3 mm screws

    • One 4.5 mm screw

    • If there is tape covering any LCD screws, peel it up with tweezers.

  33. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 33, 2 resimden 1. : adım 33, 2 resimden 2.
    • Do not attempt to fully remove the LCD. It is still adhered in place and connected to the iPad by several cables at the home button end. Lift only from the front-facing camera end.

    • Insert the flat end of a spudger under the LCD between it and the LCD shield plate and lift gently.

    • Be very careful not to get the spudger under the shield plate. It must be between the LCD and the shield.

    • Even bending the LCD slightly can permanently damage it, so be extremely careful as you lift.

    • You can try these alternate removal methods to reduce your chance of cracking the LCD during the removal process:

    • Run a thin string (like floss or fishing line) under the display, starting from the top then working your way down

    • Use a thin, flexible card or plastic money note to cut through the adhesive starting from the top.

  34. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 34, 3 resimden 1. : adım 34, 3 resimden 2. : adım 34, 3 resimden 3.
    • The LCD is secured by mild adhesive that should be loosened before you flip the LCD up from its shield plate.

    • Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad.

  35. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 35, 2 resimden 1. : adım 35, 2 resimden 2.
    • Two wide strips of tape connect the LCD to the speakers.

    • Hold the LCD with one hand, and the rear body of the iPad with the other.

    • Do not attempt to fully remove the LCD from the iPad.

    • Gently pull the LCD away from the speakers to separate the tape, being careful not to pull on the digitizer cable.

  36. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 36, 2 resimden 1. : adım 36, 2 resimden 2.
    • Do not attempt to fully remove the LCD. It is still connected to the iPad by several cables at the home button end. Lift only from the front-facing camera end.

    • Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.

    • Be gentle and keep an eye on the LCD cables as you flip the display over.

    • Lay the LCD on the front panel glass to allow access to the display cables.

  37. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 37, 3 resimden 1. : adım 37, 3 resimden 2. : adım 37, 3 resimden 3.
    • Slide the tip of a spudger between the LCD and the adhesive tabs to free the display.

    • Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables.

  38. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 38, 1 resimden 1.
    • Remove the seven 1.8 mm Phillips #00 screws from the LCD shield plate.

  39. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 39, 3 resimden 1. : adım 39, 3 resimden 2. : adım 39, 3 resimden 3.
    • Use the flat end of a spudger to pry the LCD shield plate up and out of the iPad.

    • Remove the LCD shield plate.

  40. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 40, 1 resimden 1.
    • Remove the following Phillips #00 screws from the display cable bracket:

    • One 2.8 mm screw

    • Three 1.4 mm screws

  41. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 41, 3 resimden 1. : adım 41, 3 resimden 2. : adım 41, 3 resimden 3.
    • Remove the display cable bracket from the iPad.

  42. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 42, 3 resimden 1. : adım 42, 3 resimden 2. : adım 42, 3 resimden 3.
    • Use the tip of a spudger to lift the home button cable up off of its socket on the logic board.

    • Fold the home button ribbon cable out of the way.

  43. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 43, 3 resimden 1. : adım 43, 3 resimden 2. : adım 43, 3 resimden 3.
    • Use the tip of a spudger to gently lift the battery connector up off its socket on the logic board.

    • Be very careful to only pry up on the battery connector and not on the socket itself. If you pry up on the logic board socket, you may break the connector entirely.

  44. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 44, 2 resimden 1. : adım 44, 2 resimden 2.
    • Use the tip of a spudger to lift the LCD connector up off its socket on the logic board.

    • Do not pry against the large IC next to the connector, or you may break it. Gently pry from the side of the connector as shown.

  45. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 45, 1 resimden 1.
    • Lift and remove the LCD from the iPad Mini 3.

  46. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 46, 2 resimden 1. : adım 46, 2 resimden 2.
    • Use the tip of a spudger to lift the digitizer cable connector straight up off of its socket.

  47. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 47, 2 resimden 1. : adım 47, 2 resimden 2.
    • Slide the flat end of a spudger under the battery side of the digitizer board to begin separating it from the rear case.

  48. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 48, 2 resimden 1. : adım 48, 2 resimden 2.
    • Lift the digitizer board up to free the last of the adhesive.

  49. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 49, 1 resimden 1.
    • Lift and remove the front panel assembly from the iPad.

  50. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 50, 2 resimden 1. : adım 50, 2 resimden 2.
    • Use the tip of a spudger to peel the tape off of the antenna cables near the logic board.

  51. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 51, 2 resimden 1. : adım 51, 2 resimden 2.
    • Use the point of a spudger to separate the adhesive holding the antennas to the right speaker.

  52. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 52, 2 resimden 1. : adım 52, 2 resimden 2.
    • Use the point of a spudger to lift the antenna cable adhesive up off the rear case.

  53. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 53, 1 resimden 1.
    • Remove the following Phillips #00 screws from the left antenna:

    • One 2.6 mm screw

    • Two 1.5 mm screws

  54. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 54, 2 resimden 1. : adım 54, 2 resimden 2.
    • Use the flat end of a spudger to loosen the foam adhesive securing the Wi-Fi antenna to the left speaker.

  55. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 55, 2 resimden 1. : adım 55, 2 resimden 2.
    • Use the flat end of a spudger to fold the wide left-hand piece of tape away from the left speaker.

  56. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 56, 3 resimden 1. : adım 56, 3 resimden 2. : adım 56, 3 resimden 3.
    • Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.

    • Gently pull the antenna cable out of the way as you work along the piece of tape to free it and keep it from resealing.

  57. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 57, 2 resimden 1. : adım 57, 2 resimden 2.
    • Pull the antenna cable from the clip behind the Lightning connector.

  58. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 58, 3 resimden 1. : adım 58, 3 resimden 2. : adım 58, 3 resimden 3.
    • Pull the wide tape toward the battery, applying constant force to peel it from the antenna cable lodged between it and the speaker.

    • Insert a plastic opening tool into the gap between the wide tape and the antenna cable, to break the adhesive connecting the two.

    • Slide the plastic opening tool along the length of the antenna cable to completely separate it from the piece of tape.

  59. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 59, 3 resimden 1. : adım 59, 3 resimden 2. : adım 59, 3 resimden 3.
    • Lift the antenna cable tape up from behind the right speaker.

  60. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 60, 2 resimden 1. : adım 60, 2 resimden 2.
    • Pull the antenna cable out from under the corner of the right speaker.

  61. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 61, 2 resimden 1. : adım 61, 2 resimden 2.
    • Use the point of a spudger to pull the antenna cable clip toward the battery to allow access to the cables.

  62. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 62, 2 resimden 1. : adım 62, 2 resimden 2.
    • De-route the antenna cable from the retaining clip.

  63. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 63, 2 resimden 1. : adım 63, 2 resimden 2.
    • Use the point of a spudger to lift the left antenna cable connector straight up off of its socket on the logic board.

  64. Bu adım çevrilmemiş. Çevrilmesine yardım edin

    : adım 64, 1 resimden 1.
    • Remove the left antenna from the iPad.

Bitiş Çizgisi

Sam Goldheart

Üyelik tarihi: 10/18/12

465.266 İtibar

538 adet Kılavuz yazıldı

Ekip

iFixit iFixit üyesi

Staff

136 Üyeler

16.573 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 6

Her zaman: 1,081