Bu sürüm, hatalı düzenlemeler içerebilir. En son doğrulanmış bellek kopyası dönün.
Neye ihtiyacın var
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Power off your iPhone before beginning disassembly.
-
Your iPhone 4 rear cover may have either two #000 Phillips screws or Apple's 5-Point "Pentalobe" screws (second image). Check which screws you have, and ensure you also have the correct screwdriver in order to remove them.
-
Remove the two 3.6 mm Pentalobe or Phillips #000 screws next to the dock connector.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Push the rear panel toward the top edge of the iPhone.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Pinch the rear panel with your fingers and lift it away from the iPhone. Alternatively, use a Small Suction Cup .
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.
-
Remove the metal clip covering the antenna connector.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the clear plastic pull tab to gently lift the battery out of the iPhone.
-
If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
-
Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use a SIM card eject tool or a paperclip to eject the SIM card and its holder.
-
Remove the SIM card and its holder.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the following two screws:
-
One 1.2 mm Phillips
-
One 1.6 mm Phillips
-
Remove the thin steel dock connector cable cover from the iPhone.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use an iPod opening tool to gently pry the dock cable connector up off the logic board from both short ends of the connector.
-
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Carefully peel the dock ribbon cable off the logic board and the lower speaker enclosure.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use a plastic opening tool to pry the lower antenna connector up off its socket on the logic board.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the 1.9 mm Phillips screw securing the bottom of the logic board to the inner case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the following five screws securing the Wi-Fi antenna to the logic board:
-
One 2.3 mm Phillips
-
Two 1.6 mm Phillips
-
One 1.4 mm Phillips
-
One 4.8 mm Phillips
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use an iPod opening tool to slightly lift the top edge of the Wi-Fi antenna away from the logic board.
-
Use the tip of a spudger to pull the Wi-Fi retaining clips away from the inner frame.
-
Remove the Wi-Fi antenna from the iPhone. Make sure you don't lose the metal clips on the top of the cover where the 4.8mm screw attaches or the 4.8mm screw. That's the primary reason for abnormal Wi-Fi performance after the reassembly.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use an iPod opening tool to carefully lift the rear camera connector up off its socket on the logic board.
-
Remove the rear camera.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the small circular white sticker (warranty sticker and water indicator) covering the screw near the battery pull tab.
-
Remove the 2.4 mm Phillips screw that was hidden underneath the sticker.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the edge of a plastic opening tool to gently pry the following connectors up and out of their sockets on the logic board:
-
Digitizer cable (pry from bottom)
-
LCD cable (pry from bottom)
-
Headphone jack/volume button cable (pry from top)
-
Top Microphone/sleep button cable (pry from top)
-
Front camera cable (pry from top)
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
Bu adımda kullanılan alet:Standoff Screwdriver for iPhones$5.49-
Remove the 4.8 mm standoff screw near the headphone jack.
-
Without this part, the motherboard could damage the ribbon cables around it.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Carefully remove the logic board from the iPhone, minding any cables that may get caught.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the edge of a plastic opening tool to lift the thin steel front camera retainer off the front camera.
-
Remove the front camera retainer.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Carefully lift the front facing camera out of the iPhone.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the following two screws securing the vibrator to the inner frame:
-
One 6 mm Phillips
-
One 1.4 mm Phillips
-
Remove the vibrator from the inner case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the edge of a plastic opening tool to pry the earpiece speaker away from the adhesive securing it to the front panel.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the two Phillips #000 screws securing the power button bracket to the outer case.
-
Carefully pull the power button bracket up and out of the outer case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use a pair of tweezers to pull the body of the headphone jack out of the outer case.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Grab the power & sensor cable near the microphone and peel it off the front panel, being careful not to rip it in the process.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Also be sure to transfer the proximity sensor foam/UV-filter adhered to the old power & sensor cable if your new one does not already come with one. It looks like a small square and can be peeled off with tweezers.
-
Transfer the bracket to your new power & sensor cable.
-
İptal et: Bu kılavuzu tamamlamadım.
509 farklı kişi bu kılavuzu tamamladı.
Ekli Belgeler
24 Yorum
I replaced the Home button and the Power & Sensor cable, along with battery. Let me explain some caveats with ifixit's parts (OEM Apple parts):
-The power-sensor part does not include a new gasket/filter for the sensor- recommend tweezers and care.
-The power-sensor cable needs the foam pad transferred with the adhesive- extreme care with removal.
-IF the power button isn't working it is likely the cable, not the button.
-I used a small ice cube tray.
-It took me an hour (I had to get up and walk away...frustration factor high with the delicate flex cables and adhesive). Lit magnifier is welcome. Definitely use a spudge stick.
-I broke 2 of the 4 shield/antenna tabs that you need to tuck down from the speaker on re-assembly. I didn't force them, but so easy to press too hard in seating the speaker.
- I do repairs on a grounded-ESD mat and wore wriststrap.
-Right screw on the power button brace is PITA to access...careful pressing on the display flex cables to access the tiny screw. Magnetize your bit!
Great guide and perfect web site. It is extremely easy to find what you are looking for and order the components you need.