Ana içeriğe geç

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

iPhone 4 Verizon Speaker Enclosure Assembly Replacement

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Neye ihtiyacın var

  1. iPhone 4 Verizon Speaker Enclosure Assembly Replacement, Speaker Enclosure Assembly: adım 1, 2 resimden 1. iPhone 4 Verizon Speaker Enclosure Assembly Replacement, Speaker Enclosure Assembly: adım 1, 2 resimden 2.
    • Remove the two 1.8 mm Phillips screws securing the dock connector cable cover to the logic board.

    • Remove the metal dock connector cable cover.

  2. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 2, 1 resimden 1.
    • Use the edge of a plastic opening tool to pry the dock cable up from its socket on the logic board.

  3. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 3, 1 resimden 1.
    • Peel the dock connector cable off the adhesive securing it to the logic board and the side of the speaker enclosure.

  4. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 4, 2 resimden 1. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 4, 2 resimden 2.
    • Remove the 1.6 mm Phillips screw securing the pressure contact to the logic board near the vibrator.

    • Remove the pressure contact.

    • When reinstalling the pressure contact, be sure to clean it with a degreaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to create wireless interference.

  5. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 5, 2 resimden 1. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 5, 2 resimden 2.
    • Use the edge of a plastic opening tool to pry the Wi-Fi antenna cable up from its socket on the logic board.

    • De-route the Wi-Fi antenna cable out from under the metal fingers attached to the logic board.

  6. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 6, 1 resimden 1.
    • Remove the two 2.4 mm Phillips screws securing the speaker enclosure assembly to the outer case.

  7. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 7, 1 resimden 1.
    • Remove the small black spacer that was under the Phillips screw near the vibrator.

  8. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 8, 3 resimden 1. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 8, 3 resimden 2. iPhone 4 Verizon Speaker Enclosure Assembly Replacement: adım 8, 3 resimden 3.
    • Use a plastic opening tool to lift the speaker enclosure assembly out of the case, being sure not to damage the EMI fingers on the attached Wi-Fi antenna.

    • Remove the speaker enclosure assembly.

    • Before reinstalling the speaker enclosure assembly's screws, be sure the Wi-Fi grounding fingers are installed below the lip in the iPhone's metal case as seen in the third picture.

    • Before reassembly, be sure to clean all metal-to-metal contact points between the grounding fingers of the Wi-Fi antenna and the case of the iPhone with a de-greaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to cause wireless interference issues.

Sonuç

To reassemble your device, follow these instructions in reverse order.

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 686