Ana içeriğe geç

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

iPhone 7 Logic Board Disconnection

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Neye ihtiyacın var

  1. iPhone 7 Logic Board  Disconnection, Logic Board Connectors: adım 1, 2 resimden 1. iPhone 7 Logic Board  Disconnection, Logic Board Connectors: adım 1, 2 resimden 2.
    • Use the flat end of a spudger to disconnect the rear-facing camera connector.

  2. iPhone 7 Logic Board  Disconnection: adım 2, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 2, 2 resimden 2.
    • Remove the following Phillips screws securing the rear camera bracket to the rear case:

    • One 1.3 mm screw

    • One 2.5 mm screw

  3. iPhone 7 Logic Board  Disconnection: adım 3, 1 resimden 1.
    • Remove the bracket.

  4. iPhone 7 Logic Board  Disconnection: adım 4, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 4, 2 resimden 2.
    • Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

  5. iPhone 7 Logic Board  Disconnection: adım 5, 1 resimden 1.
    • Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

  6. iPhone 7 Logic Board  Disconnection: adım 6, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 6, 2 resimden 2.
    • Remove the upper cable bracket.

  7. iPhone 7 Logic Board  Disconnection: adım 7, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 7, 2 resimden 2.
    • Use the flat end of a spudger to disconnect the upper cable connector.

  8. iPhone 7 Logic Board  Disconnection: adım 8, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 8, 2 resimden 2.
    • Remove the Phillips screws securing the Wi-Fi antenna:

    • Three 1.2 mm screws

    • One 1.7 mm screw

  9. iPhone 7 Logic Board  Disconnection: adım 9, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 9, 2 resimden 2.
    • Remove the top left antenna.

  10. iPhone 7 Logic Board  Disconnection: adım 10, 1 resimden 1.
    • Remove the following Phillips screws:

    • One 1.3 mm screw

    • One 2.2 mm screw

  11. iPhone 7 Logic Board  Disconnection: adım 11, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 11, 2 resimden 2.
    • Remove the bracket.

  12. iPhone 7 Logic Board  Disconnection: adım 12, 1 resimden 1.
    • Remove the 2.2 mm standoff screw from the grounding bracket.

    • Standoff screws are best removed using an [bağlı ürün eksik veya kapalı: IF145-343] and driver handle.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  13. iPhone 7 Logic Board  Disconnection: adım 13, 2 resimden 1. iPhone 7 Logic Board  Disconnection: adım 13, 2 resimden 2.
    • Use tweezers to gently bend the logic board grounding bracket out of the way.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Evan Noronha

Üyelik tarihi: 02/05/15

223.223 İtibar

168 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 184