Eşyalarını Tamir Et Topluluk Mağaza

iRobot Roomba 551 Bumper Sensor Replacement

Giriş

Is your Roomba banging its head against the wall? Follow this guide to replace the bumper sensor.

Neye ihtiyacın var

  1. iRobot Roomba 551 Bumper Sensor Replacement, Side Brush: adım 1, 1 resimden 1.

    • Place your Roomba upside-down on a hard surface.

    Düzenle

  2. iRobot Roomba 551 Bumper Sensor Replacement: adım 2, 1 resimden 1.

    • While holding the side brush in place, use a Phillips #1 screwdriver to remove the 4.5mm screw from the center of the brush.

    Düzenle

  3. iRobot Roomba 551 Bumper Sensor Replacement: adım 3, 1 resimden 1.

    • Gently pull upwards on the brush to remove it.

    Düzenle

  4. iRobot Roomba 551 Bumper Sensor Replacement, Bottom Plate: adım 4, 1 resimden 1.

    • Rotate the Roomba upside-down so the bottom is facing towards you.

    Düzenle

  5. iRobot Roomba 551 Bumper Sensor Replacement: adım 5, 2 resimden 1. iRobot Roomba 551 Bumper Sensor Replacement: adım 5, 2 resimden 2.

    • Using a Phillips #2 screwdriver, remove the captive screws that hold the bottom plate in place.

    Düzenle

  7. iRobot Roomba 551 Bumper Sensor Replacement: adım 6, 1 resimden 1.

    • Carefully lift the bottom plate.

    • The battery is only secured in place by the bottom plate, and may fall out once the bottom plate is removed.

    Düzenle

  8. iRobot Roomba 551 Bumper Sensor Replacement, Bumper: adım 7, 3 resimden 1. iRobot Roomba 551 Bumper Sensor Replacement, Bumper: adım 7, 3 resimden 2. iRobot Roomba 551 Bumper Sensor Replacement, Bumper: adım 7, 3 resimden 3.

    • With a Phillips #1 screwdriver, remove the ten 12mm screws located along the bottom of the bumper.

    Düzenle

  9. iRobot Roomba 551 Bumper Sensor Replacement: adım 8, 1 resimden 1.

    • Lift the bottom cover and set it to the side.

    Düzenle

  10. iRobot Roomba 551 Bumper Sensor Replacement: adım 9, 2 resimden 1. iRobot Roomba 551 Bumper Sensor Replacement: adım 9, 2 resimden 2.

    • Flip the Roomba over, grasp the bumper, and gently lift to remove.

    • The battery is not secured in place once the bottom plate has been removed, and may fall out when the Roomba is turned right-side up.

    Düzenle

  11. iRobot Roomba 551 Bumper Sensor Replacement, Bumper Sensor: adım 10, 1 resimden 1.

    • Flip the Roomba so that the bottom is facing you.

    Düzenle

  12. iRobot Roomba 551 Bumper Sensor Replacement: adım 11, 2 resimden 1. iRobot Roomba 551 Bumper Sensor Replacement: adım 11, 2 resimden 2.

    • Remove the two 5mm screws located near the center of the bumper using a Phillips #1 screwdriver.

    Düzenle

  13. iRobot Roomba 551 Bumper Sensor Replacement: adım 12, 1 resimden 1.

    • Pull gently on the bottom of the sensor to remove.

    Düzenle

  14. iRobot Roomba 551 Bumper Sensor Replacement: adım 13, 3 resimden 1. iRobot Roomba 551 Bumper Sensor Replacement: adım 13, 3 resimden 2. iRobot Roomba 551 Bumper Sensor Replacement: adım 13, 3 resimden 3.

    • Flip the bumper over and lift the sensor from its compartment.

    • You are now free to replace the bumper sensor.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

Cody Rhoads

Üyelik tarihi: 01/16/14

348 İtibar

2 adet Kılavuz yazıldı

Rozetler: 8

+5 tane daha rozet

Ekip

Cal Poly, Team 13-14, Regan Winter 2014 Cal Poly, Team 13-14, Regan Winter 2014 üyesi

CPSU-REGAN-W14S13G14

4 Üyeler

19 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 3

Her zaman: 4,652