Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

Giriş

Is your Roomba not able to sense surrounding obstacles, preventing it from avoiding such barriers? If so, here is the guide to fix the problem with a simple change of the bumper sensor. All you need are the standard #0 and #1 Phillips Screwdriver heads in order to remove the two types of screws involved with this replacement.

  1. Flip the iRoomba over so that the underside is facing up. Using the Phillips #0 screwdriver, remove the 4.0mm screw in the center of the yellow side brush.
    • Flip the iRoomba over so that the underside is facing up.

    • Using the Phillips #0 screwdriver, remove the 4.0mm screw in the center of the yellow side brush.

    • Remove the yellow side brush.

  2. Remove the two 3.5mm Phillips screws that hold the battery cover onto the Roomba with a Phillips #0 screwdriver. Remove the battery cover. Remove the battery cover.
    • Remove the two 3.5mm Phillips screws that hold the battery cover onto the Roomba with a Phillips #0 screwdriver.

    • Remove the battery cover.

  3. Remove the two remaining 3.5mm Phillips #0 screws that attach the base-plate to the bottom of the Roomba. Remove the entire base-plate from the bottom of the Roomba. Remove the entire base-plate from the bottom of the Roomba.
    • Remove the two remaining 3.5mm Phillips #0 screws that attach the base-plate to the bottom of the Roomba.

    • Remove the entire base-plate from the bottom of the Roomba.

  4. LCD iPhone Ekran Tamir Kit'leri

    Ömür Boyu Garantimiz kapsamındaki bütçe seçeneği.

    Shop Kits

    LCD iPhone Ekran Tamir Kit'leri

    Onarım maliyetlerini düşürün, kaliteyi değil.

    Shop Kits
  5. Remove the ten 3mm screws that attach the bumper guard to the bumper with a Phillips #1 screwdriver. Remove the bumper guard. Remove the bumper guard.
    • Remove the ten 3mm screws that attach the bumper guard to the bumper with a Phillips #1 screwdriver.

    • Remove the bumper guard.

  6. Be careful when removing the bumper from the Roomba to prevent damage to the sensor wires. Remove slowly! Lift up the Roomba so that its bumper is not resting on anything, and slowly separate the bumper from the device.
    • Be careful when removing the bumper from the Roomba to prevent damage to the sensor wires. Remove slowly!

    • Lift up the Roomba so that its bumper is not resting on anything, and slowly separate the bumper from the device.

  7. Remove the two 3mm screws that attach the sensor connector to the bumper/sensor with a #1 Phillips Screwdriver. Carefully detach the sensor connector from the bumper and the sensor. Carefully detach the sensor connector from the bumper and the sensor.
    • Remove the two 3mm screws that attach the sensor connector to the bumper/sensor with a #1 Phillips Screwdriver.

    • Carefully detach the sensor connector from the bumper and the sensor.

  8. The sensor is now loose on the bumper. Be careful not to rapidly move the bumper for fear of dislodging the sensor and breaking it. Flip the bumper over, ensuring the sensor remains inside the sensor compartment.
    • The sensor is now loose on the bumper. Be careful not to rapidly move the bumper for fear of dislodging the sensor and breaking it.

    • Flip the bumper over, ensuring the sensor remains inside the sensor compartment.

    • Gently remove the bumper from the black infrared sensor.

Sonuç

To reassemble your device, follow these instructions in reverse order.

7 farklı kişi bu kılavuzu tamamladı.

Jacob Lindberg

Üyelik tarihi: 19-04-2017

290 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team S14-G3, Banghart Spring 2017 Cal Poly, Team S14-G3, Banghart Spring 2017 üyesi

CPSU-BANGHART-S17S14G3

4 Üyeler

10 adet Kılavuz yazıldı

Bir Yorum

Can not get to the plug-in area on the board to replace sensor this way. DOES NOT work this way.

jkeysgate - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 3

Son 7 gün: 12

Son 30 gün: 69

Her zaman: 3,452