Eşyalarını Tamir Et Topluluk Mağaza

三星盖乐世 S7 Edge 后壳玻璃更换

Uyarı: Ön koşul olan bir kılavuzu düzenliyorsunuz. Yapacağınız herhangi bir değişiklik bu adımın yer aldığı bütün 4 kılavuzları etkileyecektir.

Kılavuza Dön
İngilizce
Çince
Önceki adım

Adım 7 çevriliyor

Adım 7
Samsung Galaxy S7 Edge Rear Glass Replacement: adım 0, 2 resimden 1. Samsung Galaxy S7 Edge Rear Glass Replacement: adım 0, 2 resimden 2.

  • To install a new back cover:

  • Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.

  • Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.

  • If you're reinstalling the old back cover, or using a back cover without adhesive pre-installed, follow this guide.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

重装后壳：

首先用镊子揭掉后盖和手机后框上残留的胶。

然后，用高浓度（至少90%）异丙醇和不起毛的布来清理粘胶的部位。擦的时候只向一个方向擦，不要来回来去地擦。这能让表面更适合新的胶来粘合。

在重新粘合新的后盖前请确保你的手机可以正常开机。

新的胶应该是预裁切在塑料片上的，如果你没有那种胶，亦可使用如Tesa 61395这样的液体强力胶水，但请注意此种胶水可能会在粘合后盖后透过其他微小缝隙或留下痕迹。

在安装完毕后，你可以将手机置于一摞书下来形成均匀的压力使新的胶附着良好。

如果你想的话，你也可以用旧有的胶粘回后盖。去掉可能会妨碍后盖整齐粘回原位的大块胶。在安装完成后，加热后盖然后加压来让后盖粘牢。请注意，这样你的手机将不会防水，但是旧的胶一般也足够使后盖粘牢。

[* icon_reminder] To install a new back cover:
- [* black] Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
+ [* black] Use [product|IF145-020|tweezers] to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
[* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
[* icon_reminder] If you're reinstalling the old back cover, or using a back cover without adhesive pre-installed, [guide|124003|follow this guide|new_window=true].
[* icon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

Katkılarınız, açık kaynak Creative Commons lisansı altında lisanslanmaktadır.