Ana içeriğe geç
Almanca
İngilizce

Dell c1760nw Clean main mechanics and make it work

Kılavuz Bilgisi

= Bitti = Eksik

      Üzerinde çalıştığınız device'ın spesifik parçasını veya bileşenini tarif edin. EÖrneğin: Pil

      Bir başlık oluştur.

      Bu 1-2 cümlelik özet, arama sonuçlarında görüntülenecektir.

      Okuyucuya, onlar daha kılavuza dalmadan önce gerekli olan arka plan bilgilerini aktarın.

      Kılavuz Adımları

      Adım 1 — Remove error 007-371

      Your Dell C1760nw ( and some other LED/laserprinter models) shows you incessantly the error 007-371? Then this repair guide is interesting for you!

      Adım 2 — Remove the paper tray

      Remove the folding paper pad, by bending it (careful) and unfixing it on one site.

      Adım 3 — Remove front housing parts

      Remove the bar at the top and the front.

      Adım 4 — Remove TopCase

      Remove two srews from the front. And to take off the cover leverage remove the tabs diagonally from the front over the latching.

      Adım 5 — Continued: Remove TopCase

      Carefully lift the cover (Attention: cable connection to the display is hanging there) and rack it to the back of the printer (move it back and forth to unhook the locking nipple): unplug the display connector (yellow lines) from the I/O board, unroute the cable and remove the cover.

      Adım 6 — Remove left housing part

      Place the printer on the right side and remove the left side panel (there are 2 lugs under the printer)

      Adım 7 — Next: Remove the left housing part

      Reposition the printer and hold the disengaged lugs in the disengaged position. Open the rear flap and slide the side panel backwards while moving away from the printer.

      Adım 8 — Remove the WLAN card

      The WLAN card is secured with a screw-> remove it, carefully unplug the WLAN card and remove the WLAN bracket together with the cable

      Adım 9 — Remove I / O card

      Loosen all connectors (pull plugs carefully out of sockets)

      Adım 10 — Remove metal plate (beneath I / O card)

      The metal plate under the I/O card (which holds the I/O card) is secured with 3 screws. Remove all 3 screws

      Adım 11 — Remove the fan

      The fan is secured to this plate with a screw (red arrow): Loosen the screw and unlock the locking device on the other side of the fan.

      Adım 12 — Unroute wiring harnesses

      Unroute all cable harnesses on the left side from the guides.

      Adım 13 — Remove other components

      A) Remove plastic bracket with gear for paper feed (2 screws) - No photo!

      Adım 14 — B) Remove main drive

      Loosen 4 screws

      Adım 15 — C) Remove board with color control

      Carefully pull the upper flexible cable out of the base

      Adım 16 — Remove the color control gear

      Next, we remove the color control gear (black, large plastic bracket with 15 meshing gears (5 screws have to be loosened).

      Adım 17 — Washing the gearwheels ...

      Washing the gearwheels.

      Adım 18 — First success

      The "before / after" evidence ;-)

      Adım 19 — Second success

      And once again: before and after

      Adım 20 — Clean the chassis

      Now the chassis should be cleaned (only for the good feeling! and because of the care...)

      Adım 21 — After assembly

      The assembly is done in reverse order... Until the printer only needs the right and front housing part plus the paper flap.

      Katkılarınız, açık kaynak Creative Commons lisansı altında lisanslanmaktadır.